CAME FA7024CB, Руководство по установке, Страница: 53 / 128

Page
21
- Manual
FA01047-EN
- 08/2018 - © C
AME S.p.A. - Original instructions
F43
Opening approach
point of the M2 motor
Adjusting as a percentage of the total travel, the gearmotor M2 opening approach starting point.
 This function only appears if the Encoder function is activated.
1
= 1% of the travel /…/
10
= 10% of the travel (
default
)
F44
Closing approach
point for motor M2
Adjusting as a percentage of the total travel, the gearmotor M2 closing approach starting point.

This function only appears if the Encoder function is activated.
1
= 1% of the travel /…/
10
= 10% of the travel (
default
)
F46 Number of motors
For setting the number of motors connected to the control panel.
OFF
= M1 and M2
(default) / ON
= M2
F49
Managing the serial
connection
For enabling the CRP (Came Remote Protocol).
OFF
/
3
= CRP (
default
)
F50 Saving data
Saving users and saved settings in memory roll.
 This function only appears if a memory roll has been fitted into the control board.
OFF
(
default
) /
ON
F51 Reading data
Uploading data saved in memory roll.
 This function only appears if a memory roll has been fitted into the control board.
OFF
(
default
) /
ON
F56 Peripheral number
To set the peripheral's number from 1 to 255 for each control board when you have a system
with several operators.
1 ----> 255
F63 COM speed
For setting the communication speed used in the CRP (Came Remote Protocol) connection
system.
0
= 1200 Baud /
1
= 2400 Baud /
2
= 4800 Baud /
3
= 9600 Baud /
4
= 14400 Baud /
5
=
19200 Baud /
6
= 38400 Baud (
default
) /
7
= 57600 Baud /
8
= 115200 Baud
F65
RIO-EDGE
wireless input [T1]
RIO-EDGE wireless safety-device to associate to one of the available functions: P0 = TOTAL STOP,
P7 = reopening during closing, P8 = reclosing during opening.
To program, see the instructions enclosed with the accessory.
 This function only appears is the control board has been fitted with a RIO-CONN card.
OFF (default) / P0 / P7 / P8
F66
RIO-EDGE
wireless input [T2]
RIO-EDGE wireless safety-device to associate to one of the available functions: P0 = TOTAL STOP,
P7 = reopening during closing, P8 = reclosing during opening.
To program, see the instructions enclosed with the accessory.
 This function only appears is the control board has been fitted with a RIO-CONN card.
OFF (default) / P0 / P7 / P8
F67
RIO-CELL
wireless input [T1]
RIO-CELL is associated to one of the available functions: P1 = reopening during closing; P2 =
reclosing during opening; P3 = partial stop; P4 = obstruction wait.
To program, see the instructions enclosed with the accessory.
 This function only appears is the control board has been fitted with a RIO-CONN card.
OFF (default) / P1 / P2 / P3 / P4
F68
RIO-CELL
wireless input [T2]
RIO-CELL is associated to one of the available functions: P1 = reopening during closing; P2 =
reclosing during opening; P3 = partial stop; P4 = obstruction wait.
To program, see the instructions enclosed with the accessory.
 This function only appears is the control board has been fitted with a RIO-CONN card.
OFF (default) / P1 / P2 / P3 / P4
U1 Entering users
Up to a maximum of 250 users can be entered and each can be associated to a function of choice
among those available. Add users via a transmitter or other control device (see the paragraph
called ADDING USERS WITH AN ASSOCIATED COMMAND).
1 = Step-step command (open-close) / 2 = Sequential command (open-stop-close-stop) / 3 =
Only open command / 4 = Partial command
U2 Deleting users
Deleting single users (see paragraph called DELETING SINGLE USERS).
OFF / ON = Enabling the deletion of single users.