CAME BXV Rapid Series, Руководство по установке

Страница: 35 / 128

p.
3
- M
an
ua
l
FA
01
005
-E
N
- 0
2/
20
18 - © C
AM
E S
.p
.A
. - T
ra
ns
la
te
d o
rig
in
al i
ns
tru
ct
io
ns
GENERAL PRECAUTIONS FOR INSTALLERS
⚠
WARNING! Important safety instructions.
Follow all of these instructions. Improper installation can cause serious bodily
harm.
Before continuing, also read the general precautions for users.
This product must only be used for its specifically intended purpose. Any other use is dan-
gerous. Came S.p.A. is not liable for any damage caused by improper, wrongful and unre-
asonable use. • This manual's product is defined by machinery directive 2006/42/CE as
"partly-completed machinery". Quasi-completed machinery is Partly-completed machinery
is a set that almost constitutes a machine, but which, alone, cannot ensure a clearly defined
application. Partly-completed machinery is only destined to be incorporated or assembled to
other machinery or other partly-completed machinery or apparatuses to build machinery that
is regulated by Directive 2006/42/CE. The final installation must be compliant with European
directive 2006/42/CE and current European reference standards. Given these considerations,
all procedures stated in this manual must be exclusively performed by expert, qualified staff •
The manufacturer declines any liability for using non-original products; which would result in
warranty loss • Keep this manual inside the technical folder along with the manuals of all the
other devices used for your automation system. • Check that the temperature range shown
on the operator is suitable to the locations where it will be installed. • Laying the cables,
installation and testing must follow state-of-the-art procedures as dictated by regulations • If
the power-supply cable is damaged, it must be immediately replaced by the manufacturer or
by an authorized technical assistance center, or in any case, by qualified staff, to prevent any
risk • During all phases of the installation make sure you have cut off the mains power source.
• The operator cannot be used with gates fitted with pedestrian doors, unless its operation
can be activated only when the pedestrian door is in safety position. • Make sure that people
are not entrapped between the gate's moving and fixed parts due to the gate's movement.
Before installing the operator, check that the gate is in proper mechanical condition, that it is
properly balanced and that it properly closes: if any of these conditions are not met, do not
continue before having met all safety requirements. • Make sure the gate is stable and the
castors function properly and are well-greased, and that it opens and closes smoothly. • The
guide rail must be well-fastened to the ground, entirely above the surface and free of any im-
pediments to the gate's movement. • The rails of the upper guide must not cause any friction.
• Make sure that opening and closing limiters are fitted • Make sure the operator is installed
onto a sturdy surface that is protected from any collisions • Make sure that mechanical stops
are already installed • If the operator is installed lower than 2.5 from the ground or from any
other access level, fit any protections and signs to prevent hazardous situations. • Do not fit
the operator upside down or onto elements that could yield to its weight. If necessary, add
reinforcements to the fastening points • Do not install door or gate leaves on tilted surfaces
• Check that no lawn watering devices spray the operator with water from the bottom up. •
Any residual risks must be indicated clearly with proper signage affixed in visible areas. All
of which must be explained to end users. • Suitably section off and demarcate the entire
installation site to prevent unauthorized persons from entering the area, especially minors
and children. • Affix cautionary signs, such as the door plate, the gate plate, wherever nee-
ded and in plain sight. • Use proper protections to prevent mechanical hazards when people
are loitering around the machinery's range of action, for example to prevent finger crushing
between the rack and pinion) • The electrical cables must run through the cable glands and
must not touch any heated parts, such as the motor, transformer, and so on). • Make sure