CAME BX241, Руководство по установке

Страница: 11 / 16

- Trimmer TCA = Automatic closing time: 1" to 120";
- Trimmer AP.PARZ. = Partial opening time: 1" to 15".
- Trimmer SENS.= amperometric sensitivity adjustment
1 ON - Automatic closure enabled
2 ON - "Open-stop-close-stop" radio control and/or button function enabled (with plug-in radiofrequency board)
2 OFF - "Open-close-reverse" radio control and/or button function enabled (with plug-in radiofrequency board)
3 ON - "Only open" radio control and/or button function enabled (with plug-in radiofrequency board)
4 ON - "Maintained action" operation enabled
5 ON - Pre-fl ashing (aperture and closure) enabled
6 ON - Obstacle detection device (motor of limit position) enabled
7 OFF - Re-aperture in closure phase enabled; activate safety device (2-C1), if not set the dipswitch to ON
8 OFF - "Stop" button enabled; activate safety device (1-2), if not set the dipswitch to ON
9 OFF - "Partial-stop" enabled; activate safety device (2-C3), if not set the dipswitch to ON
10 Not used
ON
OFF
/.
+ T.P.A. - + T.P.A. - + T.A.C. - + T.A.C. - + SENS. - + SENS. -
&# & - &! .
#/.42
/,"/
!2$
#/.42
/,"/
!2$
40!
•
••
••
••
••
••
••
•
••
•••
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
••
•
••
•
•
••
•
••
•
••
•
••
•
••••
•••
•
••
•
••
•
••
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
•
•
•
•
•
•
•
• • • • •• • •
% 0 # #
6 !#
,4 ,4 , ,
"!44%29
$
#
"
!
4!# 3%.3
02/'2!-
#(
!&!&
11
A
ll t
h
e d
at
a a
n
d i
n
fo
rm
at
io
n c
o
n
ta
in
ed h
er
ei
n i
s c
o
n
si
d
er
ed s
u
b
je
ct to c
h
an
g
e a
t a
n
y t
im
e a
n
d a
t o
u
r d
is
cr
et
io
n
ENGLISH
2) The AF board should
AL WAYS be in sert ed when the
pow er is off.
1) On AM transmitters operating at 433.92 MHz (TOP and
TAM series), position the jumper connection on circuit card
AF43S as shown on the sheet.
Frequency/MHz Radiofrequecy Transmitter
FM 26.995 AF130 TFM
FM 30.900 AF150 TFM
AM 26.995 AF26 TOP
AM 30.900 AF30 TOP
AM 433.92 AF43S / AF43SM TAM / TOP
AM 433.92 AF43SR ATOMO
AM 40.685 AF40 TOUCH
6.8 Adjustments
6.7 Function selections
7.1 Prepare the radio board (AF)
7 Installation procedure of the transmitter for remote control
Read the three steps below before beginning installation procedures:
- prepare the radio board (paragraph 7.1);
- procedure for codifying the transmitter (paragraph 7.2);
- memorizing the code on the command board (paragraph 7.3).
TOP TAM
AF - Radio board
Motherboard