background image

          terms and 

conditions

of receipt of the relevant Chip Cards by the Customer. Liability for 

damages due to defects is limited in accordance with the provisions of 

Section 8 of these GTC.

3.10 The provision of the Services by 1NCE is otherwise subject to the 

provisions of these GTC and applicable laws and regulations, in 

particular those of the TKG.

3.11 For operational reasons and/or reasons of technological development, 

1NCE shall be entitled to change the specifi cations and functionalities 

of the Services and to adapt the Service Description accordingly, 

provided that the respective change does not reduce or impair the 

essential performance characteristics of the Services. This may 

also result in changed system requirements to be observed by the 

Customer (see Section 4.5 of these GTC). Sentences 1 and 2 shall 

apply mutatis mutandis if third parties from whom 1NCE obtains 

underlying services necessary for the provision of the Services change 

their services.

4.  Terms of use / Cooperation obligations of the Customer
4.1  The Customer may only use the Services in accordance with these 

GTC and the Service Description for its own purposes.

4.2  The Customer is not permitted to make the Services available to 

third parties for their sole use or commercial use or to otherwise 

pass them on to third parties without the prior permission of 1NCE. 

In particular, the Customer is also not entitled to act as a provider of 

telecommunications services using the Chip Cards made available to 

it for use and to offer mobile communications services, switching or 

interconnection services to third parties.

4.3  The Services may not be used abusively or in any other illegal manner 

in violation of legal prohibitions in the Federal Republic of Germany 

or at the respective place of use. In particular, no legally prohibited, 

unsolicited information, goods and other services shall be sent by the 

Customer. Furthermore, (a) no information with unlawful or immoral 

content may be transmitted and no reference may be made to such 

information; (b) connections may not be established which serve the 

purpose that the Customer or a third party is to receive payments 

or other consideration on account of the connection or the duration 

of the connection (e.g. in return for SMS to chat lines or advertising 

hotlines), or which do not serve the purpose of direct communication 

with another subscriber, but only for the purpose of establishing 

the connection and/or the duration of the connection; (c) national 

and international copyrights, trademarks, patents, names and other 

intellectual property rights and personal rights of third parties must be 

observed.

4.4  1NCE shall be entitled, in the event of serious breaches by the 

Customer of the obligations incumbent upon it in accordance with 

Section 4.3 of these GTC, to block the Services at the Customer’s 

expense, without the Customer being exempted from the obligation to 

pay the agreed charges in this respect. The regulation of Section 45o 

TKG regarding the blocking of call numbers remains unaffected.

4.5  The Customer undertakes to comply with the system requirements 

for the use of the Services specifi ed in the Service Description and to 

comply with the cooperation obligations specifi ed in these GTC and 

the Service Description. To the extent non-observance of the system 

requirements in accordance with sentence 1 by the Customer can 

have a detrimental effect on network operation, in particular on network 

security or network integrity (e.g. in the case of operation of non-

network-compliant terminal devices by the Customer), 1NCE shall in 

particular be entitled to block the relevant Chip Card; any further rights 

and claims of 1NCE shall remain unaffected.

4.6  The Customer is further obliged to

a)  notify 1NCE’s customer service without undue delay of the loss of 

the Chip Card provided to the Customer;

b)  notify 1NCE without undue delay in text form of any change 

in its name or company name, legal form, address or invoice 

recipient, or to have a third party authorized to do so notify 1NCE 

accordingly (see also Section 2.3 sentence 3 [second half] of 

these GTC);

c)  to keep personal access data (such as passwords) confi dential 

and to change them without undue delay if it is suspected that 

unauthorized persons may have gained knowledge of them;

d)  to make backup copies of all Customer data used in connection 

with the Services at reasonable intervals in order to enable lost 

or destroyed Customer data to be restored with reasonable effort; 

and

e)  in the event of a request for information addressed to 1NCE by 

authorities or courts in connection with the Services, to provide 

1NCE without delay with the information requested by 1NCE in 

relation to the Customer and, in particular, to transmit to 1NCE 

documents and information necsary to enable 1NCE to comply 

with the relevant request for information.

5.  Charges / Objections of the Customer
5.1  The Customer shall pay the charges agreed between the Parties 

in accordance with Section 2 of these GTC for the Services. Within 

the framework of the conclusion of the contract, the Customer may 

choose between different payment methods offered by 1NCE. Unless 

otherwise agreed between the Parties, the charges to be paid by the 

Customer for the purchase of additional Quotas in accordance with 

Section 3.3 sentence 2 of these GTC shall be determined by the price 

list of 1NCE valid at the time of this purchase.

5.2  All charges are to be paid by the Customer in advance (prepaid). 

Payments by the Customer must be made within 14 days of receipt of 

the invoice at the latest.

5.3  The Chip Card shall not be activated for the fi rst time and dispatched 

until 1NCE has been able to record the complete receipt of payment 

both for the charge attributable to the Chip Card (this includes the 

purchase price for the Chip Card and the fees for the respective 

original Quota) and any additional charge owed by the Customer 

(e.g. for the dispatch of the Chip Card). Also, the reactivation of a 

temporarily deactivated Chip Card (see Section 3.3 sentence 2 of 

these GTC) will only take place as soon as 1NCE has been able to 

record the complete receipt of payment with regard to an additional 

Quota purchased by the Customer at a later date.

5.4  If the Customer orders several Chip Cards within the scope of 

one order, the activation and dispatch of all ordered Chip Cards in 

accordance with Section 5.3 of these GTC will only take place as a 

whole when 1NCE has been able to record the complete receipt of 

payment for all charges relating to the ordered Chip Cards. 1NCE is 

not obliged to provide partial deliveries; therefore, no activation or 

dispatch of partial quantities of ordered Chip Cards will take place.

5.5  All charges shall be in Euro plus any applicable statutory value added 

tax (which shall also be borne by the Customer). Any taxes, levies, 

duties and similar charges incurred outside the Federal Republic 

of Germany in connection with the Services shall be borne by the 

Customer. This also applies in particular to the value added tax to be 

borne by the service recipient in accordance with the provisions of 

the EU VAT system directive in its EU member state (reverse charge 

procedure).

5.6  The Customer may only set off payment claims asserted by 1NCE 

against counterclaims which are undisputed or have become res 

judicata. The same applies to any rights of retention asserted by the 

Customer.

5.7  Complaints raised by the Customer against the amount of the 

connection charges or other usagedependent charges vis-à-vis 1NCE 

are subject to the legal provisions of Sections 45i, 45j TKG. Therefore, 

in particular the following applies: Complaints of the Customer must be 

made within eight weeks of the connection being established. Failure 

to make such complaints in good time shall be deemed approval. The 

Customer’s statutory claims in the event of complaints after the lapse 

of the said time period shall remain unaffected.

6.  Contract Term / Termination
6.1  The contractual relationship is concluded for an indefi nite period of 

time.

6.2  The contractual relationship in respect of each individual Chip Card 

may be terminated by
a)   the Customer at any time without period of notice; and
b)   1NCE with a period of two weeks, but not before the end of the 

ActivationPeriod.

6.3  The right of both Parties to terminate the contractual relationship 

exceptionally for good cause (außerordentliche Kündigung aus 

wichtigem Grund) remains unaffected.

6.4  No compensation for any unused Quota that may still exist at the time 

of termination of the contract with regard to the relevant Chip Card 

shall be payable to the Customer unless 1NCE is responsible for an 

exceptional termination through the Customer for good cause (see 

Section 6.3 of these GTC).

6.5  Any termination must be made in text form in order to be valid.
7.  Rights of use / IP rights of third parties
7.1  To the extent 1NCE provides the Customer with software for use within 

the scope of the Services, 1NCE grants to the Customer a simple right 

to use the software for the duration of the respective contract term, 

which is limited to the countries specifi ed in the Service Description. 

This right of use is (a) neither sublicensable nor transferable and (b) 

subject to the restrictions resulting from these GTC and the Service 

Description. Further rights to use the software are not granted to the 

Customer. Similarly, the Customer shall not be granted any rights to 

edit the software unless such rights are required by mandatory law.

7.2  If, in respect of the rights of use referred to in Section 7.1 above, 

a violation of third party intellectual property rights is asserted or 

threatened to be asserted, 1NCE shall be entitled, at its own discretion 

and expense, to secure the Customer’s right of continued use or to 

modify the software in order to prevent infringements of intellectual 

property rights or to temporarily cease the provision of the software. 

Any claims of the Customer are excluded if and to the extent that the 

infringement relates to an unauthorized modifi cation of the software 

by the Customer or its other use by the Customer in violation of the 

provisions of these GTC or the Service Description.

Содержание 8K01MI-0515

































Отзывы: