Cambium Networks XE5-8 Скачать руководство пользователя

Страница: 48 / 52

Chapter 2: Packaging and Installation of Access Point

Mounting XV2-22H

The XV2-22H units are mounted by using one of the following mounting techniques:

⚫

Single gang mounting, or

⚫

Wall mounting

Single gang mounting

Place single-gang wall bracket on the gang box and secure with at least 2 screws.

Connect the Ethernet cable to the upper RJ-45 port labeled Eth1/PoE at the rear side of XV2-22H
to provide connectivity. Use the other RJ-45 port labeled Pass-Through for any additional cable
that might need to pass through XV2-22H.

Align the two slots on the rear side of the XV2-22H with two hooks on the bracket.

Secure XV2-22H to the bracket with a screw at the bottom edge of XV2-22H using a standard Torx
security screw or standard Philips head screw.

Содержание XE5-8





















































Результаты поиска

Содержание XE5-8

Отзывы:

Похожие инструкции для XE5-8

Бренды по названию

Популярные бренды

Cambium Networks XE5-8, Руководство по установке оборудования

Результаты поиска

Содержание XE5-8

Отзывы:

Похожие инструкции для XE5-8

Бренды по названию

Популярные бренды