manualshive.com logo in svg

Cambium Networks PTP 820 Series, Руководство по установке

Поделиться
Скачать
Cambium Networks PTP 820 Series Скачать руководство пользователя страница 9

Installation Guide for RFU-D-HP 

 

Page 9 of 179 

 

 

Chapter 1

 

 About This User Guide

 

This guide describes RFU-E installation procedures and provides additional information concerning system parts and 
frequency bands. 

This guide contains the following chapters: 

•

 

Chapter 1: Product description

 

•

 

Error! Reference source not found.Error! Reference source not found.

 

•

 

Error! Reference source not found.Error! Reference source not found.

 

•

 

Error! Reference source not found.Error! Reference source not found.

 

 

•

 

Error! Reference source not found.

 

Error! Reference source not found.

 

•

 

Error! Reference source not found.Error! Reference source not found.

 

Contacting Cambium Networks

 

Support website: 

https://support.cambiumnetworks.com

 

Main website: 

http://www.cambiumnetworks.com

 

Sales enquiries: 

[email protected]

 

Support enquiries: 

https://support.cambiumnetworks.com

 

Repair inquiries 

https://support.cambiumnetworks.com

 

Telephone number list: 

http://www.cambiumnetworks.com/support/contact-support

 

Address: 

Cambium Networks Limited, 
Linhay Business Park, 
Eastern Road, Ashburton, 
Devon, UK, TQ13 7UP 

Purpose

 

Cambium Networks Point-To-Point (PTP) documents are intended to instruct and assist personnel in the operation, 
installation and maintenance of the Cambium PTP equipment and ancillary devices. It is recommended that all 
personnel engaged in such activities be properly trained. 

Cambium disclaims all liability whatsoever, implied or express, for any risk of damage, loss or reduction in system 
performance arising directly or indirectly out of the failure of the customer, or anyone acting on the customer's behalf, 
to abide by the instructions, system parameters, or recommendations made in this document. 

Cross references

 

References to external publications are shown in italics. Other cross references, emphasized in blue text in electronic 
versions, are active links to the references. This document is divided into numbered chapters that are divided into 
sections. Sections are not numbered, but are individually named at the top of each page, and are listed in the table of 
contents. 

Feedback

 

We appreciate feedback from the users of our documents. This includes feedback on the structure, content, accuracy, 
or completeness of our documents. Send feedback to 

[email protected]

. 

Содержание PTP 820 Series




















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды