Cambium Networks PTP 820 Series Скачать руководство пользователя страница 112

Страница: 112 / 179

Installation Guide for RFU-D-HP

Page 112 of 179

Make sure the following items are attached to the Dual Coupler or Splitter before attaching the Diplexer

units:

•

Four plastic washers on either side of the Dual Coupler or Splitter on the surface around the screw

threads for the Diplexer unit.

•

Smooth tin foil sheets on the side facing the waveguide interfaces. Make sure they are properly

placed and not bent or wrinkled. It is also important to ensure that the tin foil sheets do not get
wrinkled or bent during installation.

Attach the Diplexer unit to the Dual Coupler or Splitter using 8 M4 screws provided with the Diplexer kit,

as shown below, using 20Nm torque.

Note

Verify that the O-rings on the Dual Coupler or Splitter are properly mounted between the Dual
Coupler or Splitter ports and the Diplexer unit.

O-Rings (Dual

Coupler/Splitter)

M8 Screws

(4 on each Diplexer)

Содержание PTP 820 Series




















































































































































































Результаты поиска

Содержание PTP 820 Series

Отзывы:

Бренды по названию

Популярные бренды

Cambium Networks PTP 820 Series, Руководство по установке

Результаты поиска

Содержание PTP 820 Series

Отзывы:

Бренды по названию

Популярные бренды