background image

 Page 4

 *   TA interruption function:
       The current traffic announcement is cancelled by pressing this key. But the TA mode
       will not be off.
 *   When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved 
      only when traffic program identification code has been received.
      When TA is ON, traffic program identification code is not received during specified time.

12.AF [ALTERNATIVE FREQUENCIES] BUTTON
      When pressed briefly, AF switching mode is selected and the state of AF switching 
      mode  is displayed by AF segment in display.
          Segment off: AF switching mode off.
          Segment on: AF switching mode on, and has RDS information.
          Segment flashing: AF switching mode on, but RDS information is not received yet.
      When AF switching mode is selected, the radio checks the signal strength of AF all 
      the time. The interval of checking time of each AFs depends on the signal strength
      of current station, from a few minutes for a strong station to a few seconds for weak 
      station. Every time that new AF is stronger than current station, it switches over to
      that frequency for very short time, and NEW FREQUENCY is displayed for 1-2 
      seconds. 
      Because the mute time of AF switching or checking time is very short, it is almost 
      inaudible in case of normal program.
      During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only 
      receive and save RDS program.
      During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can
      only receive and save RDS program. 
      When pressed long, AF mode is converted to REGION ON/OFF mode.
      REG ON: 
      AF switching or PI SEEK is implemented to the station which have all PI codes
      are same as current station.(PI CODE is checked when AF CHECK in progress)
      REG OFF:
      The regional code in the format of PI code is ignored when AF switching or PI
      SEEK is implemented.(PI CODE and COVERAGE AREA is not checked when
      AF CHECK in progress)

13. AS/PS BUTTON (Auto-storage /Preset scan)
      During radio mode:
  1) When pressing and holding for more than 1 second, the radio searches from the
      current frequency and checks the signal strength level until 6 stations are found.
      And then the 6 stations frequency are preset to the corresponding preset memory
      numbered bank. The auto-storage operation is implemented in each selected band. 
      When the auto-storage operation is finished, the radio execute the Preset scan. 
  2) When pressed briefly, the radio searches for each preset station in the current 
      band and holds at that preset number for 5 seconds whlie releasing mute, and then
      searches again.  
      During SD/MMC  or USB mode:
      Press AS/PS button, it will activate TRACK SEARCH mode . The LCD will display 
      TRK 0/00/000(dependent on the total number of tracks in the SD card or USB stick) 
      and flash the 0 on the biggest digit position. Then press the VOL+ or VOL- button 
      to select a number on the flashing digit position from 0 ~ 9. Then press AS/PS 
      button to confirm the number and flash the 0 on next smaller digit position. With 
      the same means, select the number on the flashing digit position with VOL+/- 
      buttons. After finishing selecting the numbers on all digits position, press SEL 
      button to play the track of the selected serial number. 
     

 Page 7

TROUBLE SHOOTING

Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.

Common Symptoms

There is no power.

Cause  

The fuse has blown.

The volume control is set too low.

There is no sound.

  The operation keys
  do not work

   The antenna cable is not connected.

   Insert the antenna cable firmly into the
   antenna socket of the device.

No radio reception.

The built-in microcomputer is not
operating properly due to noise

 Switch the device off and on again. Or press
 the RESET button to resume the program. 

The device has not been correctly
connected. 

Turn up the volume properly.

Check the power and earth connection
according to the wiring diagram.

Replace another fuse according to the wiring
diagram.

The car ignition is switched off.

If the power supply is properly connected to
the car accessory, switch the ignition key to
   ON  or  " ACC 

 " 

 " .

Solution

In automatic search
mode the radio does
not stop at a trans-
mitting station.

Tune in to a radio station manually.

The transmission signals are too
weak.

Содержание RMD 210











Отзывы: