Page 4
* TA interruption function:
The current traffic announcement is cancelled by pressing this key. But the TA mode
will not be off.
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved
only when traffic program identification code has been received.
When TA is ON, traffic program identification code is not received during specified time.
12.AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressed briefly, AF switching mode is selected and the state of AF switching
mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all
the time. The interval of checking time of each AFs depends on the signal strength
of current station, from a few minutes for a strong station to a few seconds for weak
station. Every time that new AF is stronger than current station, it switches over to
that frequency for very short time, and NEW FREQUENCY is displayed for 1-2
seconds.
Because the mute time of AF switching or checking time is very short, it is almost
inaudible in case of normal program.
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save RDS program.
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can
only receive and save RDS program.
When pressed long, AF mode is converted to REGION ON/OFF mode.
REG ON:
AF switching or PI SEEK is implemented to the station which have all PI codes
are same as current station.(PI CODE is checked when AF CHECK in progress)
REG OFF:
The regional code in the format of PI code is ignored when AF switching or PI
SEEK is implemented.(PI CODE and COVERAGE AREA is not checked when
AF CHECK in progress)
13. AS/PS BUTTON (Auto-storage /Preset scan)
During radio mode:
1) When pressing and holding for more than 1 second, the radio searches from the
current frequency and checks the signal strength level until 6 stations are found.
And then the 6 stations frequency are preset to the corresponding preset memory
numbered bank. The auto-storage operation is implemented in each selected band.
When the auto-storage operation is finished, the radio execute the Preset scan.
2) When pressed briefly, the radio searches for each preset station in the current
band and holds at that preset number for 5 seconds whlie releasing mute, and then
searches again.
During SD/MMC or USB mode:
Press AS/PS button, it will activate TRACK SEARCH mode . The LCD will display
TRK 0/00/000(dependent on the total number of tracks in the SD card or USB stick)
and flash the 0 on the biggest digit position. Then press the VOL+ or VOL- button
to select a number on the flashing digit position from 0 ~ 9. Then press AS/PS
button to confirm the number and flash the 0 on next smaller digit position. With
the same means, select the number on the flashing digit position with VOL+/-
buttons. After finishing selecting the numbers on all digits position, press SEL
button to play the track of the selected serial number.
Page 7
TROUBLE SHOOTING
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
Common Symptoms
There is no power.
Cause
The fuse has blown.
The volume control is set too low.
There is no sound.
The operation keys
do not work
The antenna cable is not connected.
Insert the antenna cable firmly into the
antenna socket of the device.
No radio reception.
The built-in microcomputer is not
operating properly due to noise
Switch the device off and on again. Or press
the RESET button to resume the program.
The device has not been correctly
connected.
Turn up the volume properly.
Check the power and earth connection
according to the wiring diagram.
Replace another fuse according to the wiring
diagram.
The car ignition is switched off.
If the power supply is properly connected to
the car accessory, switch the ignition key to
ON or " ACC
"
"
" .
Solution
In automatic search
mode the radio does
not stop at a trans-
mitting station.
Tune in to a radio station manually.
The transmission signals are too
weak.
Содержание RMD 210
Страница 1: ......
