![background image](http://html1.mh-extra.com/html/caliber/rmd-210/rmd-210_instruction-manual_3454410003.webp)
Page 2
Page 9
1) TA SEEK/TA ALARM:
TA SEEK mode: when newly tuned station does not receive TP information for 5
seconds, the radio retunes to next station which has a different PI to the last station,
but has the TP information.
When TP information gets lost at the current station for retune time which is set by
RETUNE SHORT(90 seconds) or RETUNE LONG(150 seconds), the radio starts to
retune to next same PI station. When same PI station does not receive in 1 cyclic
search, the radio retunes to next station with TP information.
TA ALARM mode: when this mode is selected, any automatic retune mode is not
activated. Only double beep sound(ALARM) will be heard.
When newly tuned station does not have TP information for 5 seconds, beeps are
sounded.
When TP information gets lost at the current station for retune time, the beep sound
will be heard.
When newly tuned station has no RDS signal, PI SEEK is suppressed .
2) PI SOUND/ PI MUTE:
PI SOUND mode: if a car cruises between buildings that could cause reflecting
signals, a phenomenon may occur, due to different PI codes being received from the
same AF source. when different PI sounds (DIP) are heard occassionally, this will
happen for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for less
than1second.
3) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not received for retune interval , the radio starts to retune to
next same PI station.
When same PI station does not receive 1 cyclic search, the radio goes to last station
and waits for 4-5 minutes until PI code is received.
RETUNE L mode: selected as 150 seconds.
RETUNE S mode: selected as 90 seconds.
4) MASK DPI/MASK ALL:
MASK DPI mode: masks only the AF which has different PI.
MASK ALL mode: masks the AF which has different PI and NO RDS signal with high
field strength.
5)BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any key is pressed.
BEEP OFF mode: The beep sound is disabled.
6) VOL LAST/VOL DEFA
VOL LAST: The radio switches on at the actual volume it had when it was last
switched off.
VOL DEFA: After pressing SEL button, AVOL will be displayed. Then you can
pre-select a constant switch-on volume by using the VOL knob.
7)CLK ON/OFF
CLK ON: Clock will always show on the display when power off.
CLK OFF: Clock will disappear on the display when power off.
3. POWER BUTTON
When the unit is power off, it will switch on by pressing any button except the
EJECT and the RELEASE button.
When the unit is power on, press and hold the power button for more than 0.5
seconds, the unit goes into power off mode.
SPECIFICATION
GENERAL
Supply Voltage DC 12V. Negative Ground
Current Consumption Max.10A
Power Output 25Watts X 4(measured at DC 14.4V)
Number of channels 2 STEREO channels.
Unit Dimensions 178[W] X 101.5[D] X 50[H] mm.
FM SECTION
Frequency range 87.5MHz -108MHz
Effective sensitivity 3uV.
I.F Frequency 10.7MHz.
AM SECTION
Frequency range 522KHz - 1620KHz
Effective sensitivity 40dB.
I.F Frequency 450KHz
RCA LINE OUT
Output 1200mV @ MAX.
SD/MMC or USB PLAYBACK
System MP3 audio system.
<=5
Frequency characteristics 20Hz -100Hz
dB
<=5
10KHz-20KHz
dB.
Signal to noise (SD/MMC & USB) 50dB [1KHz] .
Содержание RMD 210
Страница 1: ......