manualshive.com logo in svg

CalAmp TTU-7 Series, Инструкция по установке, Страница: 14 / 30

Поделиться
Скачать
CalAmp TTU-7 Series Скачать руководство пользователя страница 14

CalAmp | TTU-7xx Install Guide 

    

 

  

Page 10 

 

MBUD-0239v2 

12.

 

Using the device mounting flanges as a template, mark the location for each of the four (4) 
mounting screws on the trailer’s top rail. 

13.

 

At each marked location, drill a 9/64” hole. 

14.

 

Install the four (4) mounting screws through the mounting flanges and into the trailer’s top rail. 

15.

 

Tighten the screws to secure device installation. 

16.

 

Remove the activation magnet from the front of the device. 

 

The activation magnet interrupts power to the device. In order to activate device reporting, you 
must remove the activation magnet.  

 

Retain the activation magnet in order to disable reporting unit upon de-installation of device. 

17.

 

Contact Customer Support, select the Installation option (#1), and then request device to asset 
(trailer) pairing in FleetOutlook. 

18.

 

Provide your name, company name, device ESN from label and Trailer Number to the Customer 
Support Representative.  

19.

 

If Reefer, follow Step #20; otherwise end of procedure. 

20.

 

Set the Disconnect Switch to the On position. 

 

End of Installation Procedure. 

 
 
 

 

Содержание TTU-7 Series































Отзывы:

Нет отзывов