background image

3

Allow for service access

Many people choose to install a decorative structure around their spa. If 

you are installing your spa with any type of structure on the outside, such 

as a gazebo, remember to allow access for service. It is always best to 

design special installations so that the spa can still be accessed.

Consider the best place for the outdoor equipment pack 

(in-ground spas only)

The  Designer  Spa  series  requires  an  external  equipment  pack.  When 

locating  the  outdoor  equipment  pack,  you  will  want  to  consider  the 

following:

The  equipment  pack  must  be  located  within  a  maximum  of  15  feet 

• 

from the spa.

Ensure  the  equipment  running  its  normal  filtration  cycles  does  not 

• 

make too much noise for spa owners and/or neighbors.

Ensure the equipment can be easily serviced for filter cleaning and 

• 

periodic inspections in the location chosen.
If you are using a gas heater, you will need to consider wind and drafts 

• 

as well as heater exhaust for proper heater placement. (See heater 

owner’s manual for important location and safety information.)
The equipment base and heater must be placed on either a 3 1/2” 

• 

cement slab or 3” paving stones.
Make sure the equipment area selected will not be in an area where 

• 

water could run or stand.
If  the  area  receives  direct  sunlight,  you  will  want  to  provide  some 

• 

protection for the equipment portion of the equipment pack.

The equipment pack and heater are delivered separately. Do not cover gas 

heaters unless properly vented. (See heater owner’s manual for important 

safety information.)

Содержание Avalon A726B

































Отзывы: