Cal Flame 2009 Barbecue Grills and Carts Скачать руководство пользователя страница 26

Страница: 26 / 32

2009 Barbecue Grills and Carts

LTR20091038, Rev. E

Appendix

www.calspas.com

All Cal Flame grills are manufactured as standard liquid propane (LP) grills and can be converted to burn

natural gas (NG). There are two steps required to convert a grill from LP to NG.

You must perform both steps.

Step 1: Switching the regulator behind the grill

Step 2: Changing the burner orifices

The conversion kit provided with your grill may include

some or all

of the parts shown at right, depending on

the size and model of your grill.
The kit contains orifices to convert main burners, rear

infrared burners, and the large infrared burner. Your

kit will have only the parts you need to convert your

grill.
Before you begin, make certain the LP gas source

has been disconnected from the grill. If you have a

cart, you do not need to remove the grill from the

cart.

To gain access to the NG regulator:

For grills, tilt the grill forward.

•

For barbecue carts, remove the back cover.

•

Step 1: Switching the regulator behind the grill

The regulator in the image below has been removed from a grill to illustrate

this procedure.

Remove the LP gas line.

Remove the cap fitting from the end of the NG gas regulator.

Place the cap fitting over the LP gas inlet.

Insert a male flared fitting (

not provided

) in the NG gas regulator.

Converting from LP to NG

WARNING! You must have an authorized service technician perform this

procedure. If these instructions are not followed exactly, a fire or explosion may

result causing property damage, personal injury or loss of life . Lloyd’s Material

Supply (L .M .S .) will not be held responsible for an improperly converted gas grill .

You will need:

13mm open end wrench

•

Male flared fitting

•

(not provided)

Pipe compound suitable

•

for natural gas

NOTE: A flared fitting is NOT included

with your grill .

If you are attaching a flex hose to the regulator,

you will need a fitting. The fitting requires a male

flare on the input end with a 1/2” MPT on the

output end. The flared male input end needs to be

the size of your flex tubing. You can also connect

the regulator directly to your NG gas service, which

will not require a flared fitting.

Содержание 2009 Barbecue Grills and Carts

































Результаты поиска

Содержание 2009 Barbecue Grills and Carts

Отзывы:

Похожие инструкции для 2009 Barbecue Grills and Carts

Бренды по названию

Популярные бренды

Cal Flame 2009 Barbecue Grills and Carts, Руководство пользователя

Результаты поиска

Содержание 2009 Barbecue Grills and Carts

Отзывы:

Похожие инструкции для 2009 Barbecue Grills and Carts

Бренды по названию

Популярные бренды