Cairox AOYG-KQTA, Руководство по установке, Страница: 14 / 18

En-14
7. FIELD SETTING
CAUTION
• Discharge the static electricity from your body before setting up the switches.
• Never touch the terminals or the patterns on the parts that are mounted on the
board.
7.1. Field setting buttons
• Remove the front panel of the outdoor unit to access the print circuit board of the
display unit.
Print circuit board buttons for various settings and LED displays are shown in the
fi gure.
S134 S133 S132 S131 S130
LED display part
Button part
7.2. Function settings
• Various functions can be set. Follow the setting method described in 7.2.1. and 7.2.2. to set as per the requirement.
Perform these settings after the indoor unit stops.
Table. Settings List
No Setting Item
LED display
Factory
setting
Content
POWER/
MODE
ERROR
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6)
1
Low noise
mode setting
Level 1
Blink
(9 times)
○ ○ ○
●
○ ○
●
By using the “Low noise mode”, the limit of the
noise level will be set to decrease the noise
level. The mode comes in 2 levels which can
be set accordingly.
To turn on the mode, use the external input
connector (P580).
*By using this mode, the cooling/heating
performance may decrease.
*Depending on the operating condition, the
noise level may not decrease even if the Low
noise mode is on.
Level 2
Blink
(9 times)
○ ○ ○
●
○
●
○
2
Peak cut
mode setting
Level 1
Blink
(9 times)
○ ○
●
○ ○ ○
●
The capacity limit can be selected when
operating with the Peak cut mode. The
operation selection can be done by external
input connector (PA580).
The lower the level, the more the effect of
energy saving, but the cooling/heating perfor-
mance decreases.
Level 2
Blink
(9 times)
○ ○
●
○ ○
●
○
Level 3
Blink
(9 times)
○ ○
●
○ ○
● ●
Level 4
Blink
(9 times)
○ ○
●
○
●
○ ○
Sign “
○
”: Lights off, “
●
”: Lights on
7.2.1. Setting for Low noise mode
(1) Switch to “Local setting mode” by pressing [MODE] button (S134) for 3 seconds or
more.
(2) Con fi rm (POWER / MODE) blinks 9 times, and press [ENTER] button (S132).
POWER/
MODE
ERROR
PUMP
DOWN
LOW NOISE PEAK CUT
(L1) (L2) (L3) (L4) (L5) (L6)
Blink
(9 times)
○ ○ ○ ○ ○ ○ ○
Sign “
○
”: Lights off, “
●
”: Lights on, () : Number of blinking
(3) Press [SELECT] button (S133), and adjust LED display as shown below. (Current
setting is displayed)
LOW NOISE
(L2) (L3)
LOW NOISE
MODE
○
Blink
Sign “
○
”: Lights off
(4) Press [ENTER] button (S132).
LOW NOISE
(L2) (L3)
LOW NOISE
MODE
○
●
Sign “
○
”: Lights off, “
●
”: Lights on
(5) Press [SELECT] button (S133), and adjust LED display as shown in below fi gure.
PEAK CUT
(L4) (L5) (L6)
Level 1
○ ○
Blink
Level 2
○
Blink
○
Sign “
○
”: Lights off
The noise of Level 2 is lower than the one of Level 1.
9379069953_IM.indb 14 9379069953_IM.indb 14 5/24/2019 9:59:20 AM 5/24/2019 9:59:20 AM