CAI Networks WebControl PLC Скачать руководство пользователя страница 5

Страница: 5 / 50

WebControl

PLC User Guide Version 3.02.17f

1 Introduction

This document provides an overview of the technical aspects of using WebControl

PLC. It describes the inputs and outputs offered by the PLC version of the

WebControl

hardware and firmware. The WebControl PLC Programming Guide is

found in chapter 6 of this document. Function, usage and syntax as well as many

examples are provided there to help you get started. WebControl

PLC is different

from the earlier WebControl

BRE. The PLC version of firmware provides greater

flexibility in I/O control; but in return, expects user to learn programming concepts

and write an assembly like PLC program. A PLC program has the ability to read

write and compare values of the available inputs, outputs, variables and timers. With

a PLC program loaded and running, WebControl

PLC can operate on its own,

without a network connection. The PLC programming module and programming

guide are provided for a learn-on-your own experience. Assistance in writing or

debugging PLC code is not provided as part of the regular technical support for

WebControl

PLC configuration.

1.1 Scope

The scope of this document is to be a guide for configuring and using the features

provided by WebControl

. The reader is expected to be technically competent in all

the technical areas within this document, and is strongly advised to use this

document alongside the other reference material listed in the reference section.

1.2 Table of Definitions

The following table is a list of definitions used though out the document.

Definition

Description

HTTP

Hypertext transfer protocol

DNS

Domain name server

SMTP

Simple mail transport protocol

SNTP

Simple network time protocol

1-wire

Special bidirectional serial data bus from Maxim

RH Relative

humidity

NetBios

Human readable name used as an alternative to an IP address for
accessing the server on a network. E.g. http://WebControlTM

IP Internet

protocol

DHCP

Dynamic host configuration protocol

ROM

Read only memory

PLC

Programmable Logic Controller

Содержание WebControl PLC



















































Результаты поиска

Содержание WebControl PLC

Отзывы:

Бренды по названию

Популярные бренды

CAI Networks WebControl PLC, Руководство пользователя

Результаты поиска

Содержание WebControl PLC

Отзывы:

Бренды по названию

Популярные бренды