manualshive.com logo in svg

CAI Networks WebControl PLC, Руководство пользователя

Поделиться
Скачать
CAI Networks WebControl PLC Скачать руководство пользователя страница 20

 WebControl

TM

 PLC User Guide Version 3.02.17f 

Copyright(c) 2008,-2013 CAI Networks, Inc.                                                            17

 

4 AUX 

System 

Inputs 

The system AUX inputs of WebControl

TM

 are used as inputs to the PLC engine (see 

section 5.1).  This section describes the connector ladled as J12. Digital and analog 

inputs come through J12 connector. 

 

Figure 9.0 WebControl

TM

 J12 Input pins 

 

4.1 Digital Inputs 

WebControl

TM

 has eight digital TTL inputs, each of which can be configured to be 

inverted upon input to the system. The PLC engine will then look for a true of false 

case of the input. TTL level 0 is defined 0-1.75V; TTL level 1 is defined as 3-5V. 

When TTL1 being used as counter/frequency measurement purpose, its counts 

pulses up to 2MHz and max count is 32bit number. Counter starts counts from rising 

edge after the falling edge. 

Содержание WebControl PLC



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды