![background image](http://html1.mh-extra.com/html/cafe-0/cdt706-series/cdt706-series_owners-manual_3311293024.webp)
49-4000042 Rev 5
23
Problem
Possible Cause
What To Do
Suds in the tub
Wrong detergent
Use only high quality automatic dishwasher detergents to
avoid sudsing.
Cascade
®
Platinum™ ActionPacs™
or
Finish
®
Quantum
®
Automatic Dishwashing Detergent
have
been approved for use in all
Café
dishwashers.
To remove suds from the tub, open the dishwasher and
let suds dissipate. Open the door, press and hold
Start
for 3 seconds, and close the door.
Rinse agent was spilled
Always wipe up rinse agent spills immediately.
Detergent left in
dispenser cups
Dishes or utensils are
blocking the detergent cup
Reposition the dishes, so the water from the lower spray
arm can flush the detergent cup. See the
Loading
section.
Reposition the tall utensils or heavy silverware that may
be keeping the dispenser cup door from opening. See
the
Loading
section.
Don’t place large bowls or pots directly under the
detergent dispenser.
Black or gray marks
on dishes
Aluminum utensils have
rubbed against dishes
Remove marks with a mild, abrasive cleaner.
Dishes don’t dry
Additional drying time is
needed
Leave door closed after the Clean light appears to allow
the fan to run an additional 90 minutes.
Select
Heated Dry/Dry - Ultra
option to add additional
drying time.
Note:
If you open the door, this fan extension will be cancelled.
Low inlet water temperature
Make sure inlet water temperature is at least 120°F.
Select
Heated Dry/Dry
.
Use
Wash Temp Boost/Boost Temp/Hi-Temp Wash
option.
Select a higher cycle, such as
Wash Temp Sani/
Sanitize Temp/Sani
or
Heavy
.
Rinse agent dispenser is empty
Check the rinse agent dispenser and fill as required.
Control panel
responded to inputs
but dishwasher
never filled with
water
Door may not be completely
closed
Make sure the door is firmly closed.
Water valve may be turned
off
Make sure water valve (usually located under the sink) is
turned on.
Flood float may be stuck
Remove Ultra-Fine filter and lightly tap the piece under the
ultra fine filter that looks like a salt shaker. Replace the filter.
Stained tub interior
White film on inside
surface— hard water
minerals
Café recommends high quality rinse agents such as
Cascade
®
Platinum™ Power Dry™ Rinse Aid
or
Finish
®
Jet-Dry
®
Rinse Aid
to help prevent hard water mineral
deposits from forming.
Run dishwasher with citric acid to remove mineral deposits.
Citric acid (Part number:
WD35X151
) can be ordered
through GE Appliances Parts. See back cover for ordering
information. Alternatively, purchase
Cascade
®
Platinum™
Dishwasher Cleaner
or
Finish
®
Dishwasher Cleaner
and follow the directions on the label.
Dishwasher won’t
run
Fuse is blown or circuit
breaker is tripped
Replace fuse or reset circuit breaker. Remove any other
appliances from the circuit.
Power is turned off
In some installations, the power to the dishwasher is
provided through a wall switch, often located next to the
disposer switch. Make sure it is on.
Control panel is locked
Unlock control panel. See the
Getting started
section.
Possible leak is detected
Some models are equipped with leak detection and the
cycle will be cancelled if a leak is detected. The display
will show “LEAK DETECTED”. Contact Café for service.
Proper Start sequence was
not followed
See the
Using the dishwasher
section.
Control panel lights
go off when you’re
setting controls
Time too long between
touching of selected pads
Each pad must be touched within 30 seconds of the
others. To relight, touch any pad again or open the door
and unlock (top control).
Troubleshooting Tips...
Before you schedule service
TROUBLESHOOTING TIPS
Содержание CDT706 Series
Страница 1: ...Owner s Manual...
Страница 4: ...49 4000042 Rev 5 3 WELCOME Notes...
Страница 30: ...49 4000042 Rev 5 3 BIENVENUE Notes...
Страница 56: ...49 4000042 Rev 5 3 BIENVENIDO Notas...