Cabletron Systems MMAC-Plus 9G536-04 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 42

Cabletron Systems MMAC-Plus 9G536-04 Скачать руководство пользователя страница 26

Installing the SmartSwitch 9000 Module

2-6

Installing the Module into the SmartSwitch 9000
Chassis

To install the SmartSwitch 9000 module, follow the steps below:

1. Remove the blank panel covering the two slots in which the module is being

installed. All other slots must be covered, if other modules are not being
installed, to ensure proper airßow and cooling.

2. Attach one end of the ESD wrist strap packaged with the SmartSwitch 9000

chassis to your wrist. Plug the other end into the ESD Wrist Strap Grounding
receptacle in the lower right corner of the SmartSwitch 9000 chassis shown in
Figure 2-4.

3. Grasp the module and slide it into the slots. Make sure that the moduleÕs

circuit card is between the card guides, as shown in Figure 2-4. Check both the
upper and lower tracks of the card. Take care that the module slides in straight
and engages the backplane connectors properly.

4. Lock down the top and bottom plastic tabs, as shown in Figure 2-4.

The INB Terminator Modules must be installed on the rear of the fourteen slot
chassis before powering up this module. The INB Terminator Modules are not
required on the six slot chassis. Refer to the

INB Terminator Modules

Installation Guide

for information and installation procedure.

NOTE

«
...
24
25
26
27
28
...
»

Содержание MMAC-Plus 9G536-04











































Отзывы:

Нет отзывов