manualshive.com logo in svg

Cabletron Systems IRM, Руководство по установке, Страница: 19 / 30

Поделиться
Скачать
Cabletron Systems IRM Скачать руководство пользователя страница 19

 

3-1

 

CHAPTER 3

INSTALLING THE  IRM

 

This chapter contains instructions for installing the Cabletron Systems 
IRM into a Cabletron Systems' MMAC. Additional instructions are 
provided on setting the mode switches and for connecting segments to the 
IRM.

 

3.1

UNPACKING THE  IRM

 

Before you install the IRM, you should visually inspect the module. 
Unpack the module as follows:

1.  Remove the shipping material covering the IRM in the shipping box.

2. Carefully remove the module from the shipping box. Leave the 

module in its conductive bag until you are ready to install it. Save the 
shipping box and materials in the event the unit has to be reshipped.

3. Visually inspect the module. If any damage appears to have occurred, 

contact Cabletron Systems' Technical Support immediately.

 

3.2

SETTING THE IRM JUMPERS

 

On the IRM are five jumpers (See Figure 3-1). Three of the jumpers, JP2, 
JP4, and JP5, can be changed. JP1 is for Cabletron Systems use only and 
should not be changed from its default positions. JP3 is not used.

 

3.2.1

 Setting the Battery Enable/Disable Jumper (JP5)

 

The Battery Enable/Disable Jumper (JP5, Fig. 3-1) allows you to enable 
or disable the Battery Backed-up RAM on the IRM. When set to the 
Enabled position, all parameters that you enter into the IRM 

Содержание IRM































Отзывы:

Нет отзывов