background image

 

3-1

 

CHAPTER 3

DEVICE/BOARD/PORT COUNTERS

 

The IRM2 DEVICE/BOARD/PORT COUNTERS Screen is the main 
access screen for IRM2 Local Management. This screen provides 
descriptive information about the network traffic passing through the 
IRM2.

 

3.1

DEVICE/BOARD/PORT COUNTERS SCREEN

 

The DEVICE/BOARD/PORT COUNTERS Screen, Figure 3-1, allows 
quick scanning of statistical information concerning the MMAC™, 
boards, and ports associated with the IRM2. You can view the number of 
bytes received, the total number of packets, the total number of receive 
and transmit collisions, and the number of errors, and the Port 
Administration and Segmentation Status.

 

Figure 3-1

Device/Board/Port Counters Screen

 

11/02/92                 DEVICE/BOARD/PORT COUNTERS

  Device Name: IRM2                      Ethernet Address: 00-00-1d-00-39-14
                                               IP Address: 132.177.118.24

                                               Device   Board 1   Port 1
  Bytes Received                              43594532 43594532  43594532

  Packets:                                      176992   176992    176992
  Errors:                                           14       14        14

  Receive Collisions:                                0        0         0
  Transmit Collisions:                               1        1         1
  Out of Window Collision:                           0        0         0
  Runt Packets:                                     11       11        11
  No Resources Available:                            0        0         0
  Frame Alignment Errors:                            3        3         3
  CRC Errors:                                        0        0         0
  Giant Packets:                                     0        0         0
  Port Admin Status:  ON                          Port Seq. Status:  ON

           EXIT  BOARD 1   PORT  1   RESET COUNTERS  COMMUNITY NAMES
       SETUP   ENABLE BOARD   DISABLE BOARD   ENABLE PORT  DISABLE PORT
                          ENABLE ALL PORTS     PORT ASSOCIATION

Содержание IRM-2/LM





































Отзывы: