manualshive.com logo in svg

Cabletron Systems Fast Network 10, Руководство пользователя

Поделиться
Скачать
Cabletron Systems Fast Network 10 Скачать руководство пользователя страница 4

 

ii

Fast Network 10 User Guide

 

FCC NOTICE

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.

 

NOTE:

 

This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial environment. 
This equipment uses, generates, and can radiate radio frequency energy and if not installed in 
accordance with the operator’s manual, may cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause interference in which case the user 
will be required to correct the interference at his own expense.

 

WARNING:

 

Changes or modifications made to this device which are not expressly approved by the 

party responsible for compliance could void the user’s authority to operate the equipment.

 

DOC NOTICE

 

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital 
apparatus set out in the Radio Interference Regulations of the Canadian Department of 
Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables 
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique 
édicté par le ministère des Communications du Canada.

 

VCCI NOTICE

 

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or 
industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference 
by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial 
and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be 
caused to radios and TV receivers, etc.

Read the instructions for correct handling.

Содержание Fast Network 10





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды