background image

General Configuration Screen

DLE22-MA,DLE32-MA,DLE23-MA and DLE33-MA User’s Guide

5-39

Screen Lockout Time (Modifiable)

Contains the maximum number of minutes that the Local Management 
application displays a module’s screen while awaiting input or action 
from a user. For example, if the number 5 is entered in this field, the user 
has up to five minutes to respond to each of the specified module’s Local 
Management screens. In this example, after five minutes of “idleness” (no 
input or action), the terminal “beeps” five times, the Local Management 
application terminates the session, and the display returns to the Password 
screen. To enter a new lockout time, refer to Section 5.15.8.

Module Uptime (Read-Only)

Displays the total time that the module has been operating.

Operational Mode (Modifiable)

This field allows the user to set the DLE2X-MA and DLE3X-MA to 
operate as a traditional switch (802.1D SWITCHING option), or an IEEE 
802.1Q switch (802.1Q SWITCHING option).

In 802.1D SWITCHING mode, the 24 ports located on the front panel, 
and each Fast Ethernet Interface Module, and HSIM port(s) are bridged to 
each other.

In 802.1Q SWITCHING mode, the DLE2X-MA and DLE3X-MA are 
able to increase their switching functionality by creating and maintaining 
IEEE port based VLANs.

For details on how to select the Operational Mode, refer to Section 5.15.9.

Management Mode (Toggle)

This field toggles between DISTRIBUTED and STAND ALONE. 

In DISTRIBUTED mode, Local Management is entered via the 
DLM6C-AA password screen, and all chassis configuration screens are 
available to the user. All other modules installed in the chassis that are set 
for distributed management may also be accessed via a connection to a 
single COM port on one of the modules. 

In STAND ALONE mode, the module is isolated from the chassis 
configuration screens, and the module may not be accessed from a module 
that is in DISTRIBUTED mode. This provides additional security for any 

Содержание DIGITAL MultiSwitch 700 DLE22-MA











































































































































































































Отзывы: