manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Руководство по установке

Поделиться
Скачать
Cabletron Systems CyberSWITCH HSIM-W6 Скачать руководство пользователя страница 78

Appendix B: Specifications and Standards Compliance

B-4

HSIM-W6 Installation Guide

WPIM-S/T

This section describes the environmental specifications and safety and approval requirements for 
the WPIM-S/T.

Safety —

This unit meets the safety requirements of UC1950, CSA 22.2 No. 950, EN 60950, 

IEC 950 73/23/EEC.

Electromagnetic Compatibility (EMC) —

This unit meets the EMC requirements of FCC 

Part 15, EN 55022, VCCI V-3, CSA/08.8 EN 50082-1, AS/NZS 3548, 89/336/EEC.

Telcom (Future) —

FCC part 68, CS-03.

WPIM-HDSL

This section describes the environmental specifications and safety and approval requirements for 
the WPIM-HDSL.

Safety —

This unit meets the safety requirements of UC1950, CSA 22.2 No. 950, EN 60950, 

IEC 950 73/23/EEC.

Electromagnetic Compatibility (EMC) —

This unit meets the EMC requirements of FCC 

Part 15, EN 55022, VCCI V-3, CSA/08.8 EN 50082-1, AS/NZS 3548, 89/336/EEC.

NEBS —

This unit meets a minimum of Level 1 NEBS requirements in accordance with Bellcore 

GR 1089.

Содержание CyberSWITCH HSIM-W6





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды