manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Руководство по установке

Поделиться
Скачать
Cabletron Systems CyberSWITCH HSIM-W6 Скачать руководство пользователя страница 19

HSIM-W6 Firmware Support

HSIM-W6 Installation Guide

2-5

•

Inverse Multiplexing (IMUX)

•

Dynamic Host Configuration Protocol (DHCP) as defined by RFC 1541

•

Network Address Translation (NAT) routing as defined by RFC 1631

•

Password Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol 
(CHAP) under PPP as defined by RFC 1994

•

Point-to-Point Protocol Link Quality Monitoring (LQM) as defined by RFC 1333

•

Point-to-Point Protocol Multilink Protocol (MP) as defined by RFC 1990

•

Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) as defined by Q.921/
Q.931

•

Frame Relay Link Management Interface (LMI) as defined by ANSI T1.617 Annex D and ITU 
Q.933 Annex A

•

Frame Relay Data Encapsulation as defined by RFC 1490

•

Frame Relay Data Compression Protocol (DCP) as defined by FRF.9

PPP is a data link layer industry standard WAN protocol for transferring multi-protocol data traffic 
over point-to-point connections. With this protocol, options such as security, data compression, 
and network protocols can be negotiated over the connection.

Frame Relay is a packet-switching data communications protocol that statistically multiplexes 
many data conversations over a single transmission link. Data compression allows Frame Relay to 
negotiate compression over Frame Relay permanent virtual circuits (PVCs).

ISDN BRI is a switched Data Link layer control protocol which uses digital signaling to place a 
call into an ISDN network. Once the call is made, PPP is then used to transfer data.

Содержание CyberSWITCH HSIM-W6





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды