BYOC Large Beaver Ram's Head Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 23

background image

Step 2

: Flip the PCB over so that the bottom or solder side is up. Insert the

three potentiometers, the two toggle switches, and the LED into the bottom
side of the PCB.

DO NOT SOLDER ANYTHING YET!!!

The LED will

have one lead that is longer than the other.

THIS WILL GO INTO THE

SQUARE SOLDER HOLE.

Don’t forget to remove the nuts and washers

from the pots and also to snap off the tabs before you do this step.

«
...
12
13
14
15
16
...
»

Содержание Large Beaver Ram's Head
























Отзывы:

Нет отзывов

Похожие инструкции для Large Beaver Ram's Head

Бренд: Mackie Страницы: 36

Бренд: Studio Technologies Страницы: 27

Бренд: Peavey Страницы: 16

Бренд: Erica Synths Страницы: 2

Бренд: Ibanez Страницы: 2

DJM-400 - CDJ-400 Package

Бренд: Pioneer Страницы: 16

Бренд: Pioneer Страницы: 28

Бренд: Pioneer Страницы: 44

DJM-400 - CDJ-400 Package

Бренд: Pioneer Страницы: 92

Бренд: Pioneer Страницы: 100

Бренд: Pioneer Страницы: 100

Бренд: Pioneer Страницы: 204

Бренд: Pioneer Страницы: 224

Бренд: KHDK Страницы: 2

Бренд: Denon Страницы: 17

Бренд: IK Multimedia Страницы: 43

Бренд: Dateq Страницы: 24

Бренд: Eventide Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды