BYOC Chancellor Overdrive Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 31

background image

18

Step 4:

Turn the entire pedal over so that the component side of the PCB if facing up.

Lift the PCB up off the pots and toggle switch about 2mm just to make sure that the back
of the PCB does not short out against that pots. Make sure the PCB is level and
symmetrically seated inside the enclosure.

Step 5:

Solder the pots and LEDs. You will solder these parts on the component side of

the PCB. After you have soldered them in place, be sure to tighten up their nuts.

«
...
16
17
18
19
20
...
»

Содержание Chancellor Overdrive
































Отзывы:

Нет отзывов

Похожие инструкции для Chancellor Overdrive

Бренд: Mad Professor Страницы: 2

Бренд: TC Electronic Страницы: 5

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 2

Бренд: Zapi Страницы: 11

Бренд: Electro-Voice Страницы: 8

Dirty Little Secret

Бренд: Catalinbread Страницы: 8

Бренд: TouellSkouarn Страницы: 11

Бренд: TC Electronic Страницы: 6

Бренд: DigiTech Страницы: 35

Бренд: Fender Страницы: 60

FILTER MACHINE FM600

Бренд: Behringer Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды