BYOC Chancellor Overdrive Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 31

background image

19

Step 6:

Connect the TIP (negative) terminal of the DC adaptor jack to the eyelet on the

PCB with 3/4 inches of hook up wire. Connect the SLEEVE of the DC adaptor jack to the
eyelet on the far right side of the PCB with 3/4 inches of hook up wire. Connect the
battery disconnect terminal of the DC adaptor jack to the eyelet more towards the center
of the PCB with 3/4 of hookup wire.

«
...
17
18
19
20
21
...
»

Содержание Chancellor Overdrive
































Отзывы:

Нет отзывов

Похожие инструкции для Chancellor Overdrive

Бренд: Tascam Страницы: 40

Flashback Mini Delay

Бренд: TC Electronic Страницы: 27

Soundcraft Vi2000

Бренд: Harman Страницы: 202

Бренд: Karel Страницы: 19

Бренд: Zoom Страницы: 45

Бренд: Behringer Страницы: 6

Бренд: Toshiba Страницы: 24

Бренд: Toshiba Страницы: 262

Бренд: Toshiba Страницы: 533

Бренд: NOVIK Страницы: 36

Бренд: Ecler Страницы: 51

Бренд: Solid State Logic Страницы: 127

Бренд: Wheatstone Страницы: 68

Mc Crypt DJ-3000

Бренд: Conrad Страницы: 32

Бренд: Darkglass Electronics Страницы: 6

Бренд: Retroman Страницы: 2

Бренд: MA Страницы: 47

Бренд: Topp Music Gear Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды