45
45
45
45
45
G B
G B
G B
G B
G B
Cause
Cause
Cause
Cause
Cause
No regenerative in salt/brine container (6).
Power supply cut off
Inlet pressure is too low.
Compressed air pressure too low.
Regenerative was not refilled in time.
Note:
Note:
Note:
Note:
Note:
If the regenerative is refilled too late or is not
If the regenerative is refilled too late or is not
If the regenerative is refilled too late or is not
If the regenerative is refilled too late or is not
If the regenerative is refilled too late or is not
refilled (meaning that the level of regenerative
refilled (meaning that the level of regenerative
refilled (meaning that the level of regenerative
refilled (meaning that the level of regenerative
refilled (meaning that the level of regenerative
falls below the minimum or the display indicates
falls below the minimum or the display indicates
falls below the minimum or the display indicates
falls below the minimum or the display indicates
falls below the minimum or the display indicates
“low-salt”), a malfunction will occur after the next
“low-salt”), a malfunction will occur after the next
“low-salt”), a malfunction will occur after the next
“low-salt”), a malfunction will occur after the next
“low-salt”), a malfunction will occur after the next
regeneration.
regeneration.
regeneration.
regeneration.
regeneration.
Cable to the valve block is defective.
Electrolysis cell overcurrent
Maintenance must be performed after every 500
regenerations.
Malfunction
Malfunction
Malfunction
Malfunction
Malfunction
Unit not supplying softened or blended water
Unit not supplying sufficient water or the flow is
insufficient.
Display indicates low salt
low salt
low salt
low salt
low salt (low salt! date time)
Display indicates Valve 1, 2, 3, or 4 is defective
Valve 1, 2, 3, or 4 is defective
Valve 1, 2, 3, or 4 is defective
Valve 1, 2, 3, or 4 is defective
Valve 1, 2, 3, or 4 is defective
Display indicates Elyse
Elyse
Elyse
Elyse
Elyse
11
11
11
11
11 T
T
T
T
Troub
roub
roub
roub
roubleshooting
leshooting
leshooting
leshooting
leshooting
S i c h g . E l y s e
D a t u m U h r z e i t
S a l z m a n g e l !
D a t u m U h r z e i t
S i c h g . V e n t 1 - 4 !
D a t u m U h r z e i t
Action
Action
Action
Action
Action
Refill regenerative. Wait approx. 1 hour
and then regenerate manually.
Re-establish electrical connection.
Increase inlet pressure (adjust pressure
reducer if necessary) and start manual regen-
eration.
Check inlet pressure and start regeneration.
The brine must be siphoned off or extracted to
The brine must be siphoned off or extracted to
The brine must be siphoned off or extracted to
The brine must be siphoned off or extracted to
The brine must be siphoned off or extracted to
the level of the sieve base. Only after this has
the level of the sieve base. Only after this has
the level of the sieve base. Only after this has
the level of the sieve base. Only after this has
the level of the sieve base. Only after this has
been done can the regenerative be refilled.
been done can the regenerative be refilled.
been done can the regenerative be refilled.
been done can the regenerative be refilled.
been done can the regenerative be refilled.
If this is done incorrectly, the softened water will
If this is done incorrectly, the softened water will
If this is done incorrectly, the softened water will
If this is done incorrectly, the softened water will
If this is done incorrectly, the softened water will
be salty.
be salty.
be salty.
be salty.
be salty.
Check the cable to the valve block and press OK
OK
OK
OK
OK
to confirm.
Contact the after-sales service staff if the mal-
function is still displayed.
Check the cable to the valve block for short
circuits and press OK
OK
OK
OK
OK to confirm.
Contact the after-sales service staff if the mal-
function is still displayed.
Contact after-sales service.
If the fault cannot be rectified by following the above instructions, please contact a specialist or our after sales service.
If the fault cannot be rectified by following the above instructions, please contact a specialist or our after sales service.
If the fault cannot be rectified by following the above instructions, please contact a specialist or our after sales service.
If the fault cannot be rectified by following the above instructions, please contact a specialist or our after sales service.
If the fault cannot be rectified by following the above instructions, please contact a specialist or our after sales service.
