Cable-in/Cable-out Operation
Wireless Hand Controller
Pairing of new Wireless Hand Controller
Wired Hand Controller
Connect Winch Hand Controller Cable
to Winch Control Box and to Hand Controller
Operating Procedure
To “Winch - Out”, Press and hold the “OUT” Button
To “Winch - In”, Press and hold the “IN” Button
To stop winching, releasing button.
The above operating procedure is the same for the Wireless
Hand Controller.
Activating Wireless Control
Press and hold the POWER Button ( ) for 3 seconds to
activate the Wireless Control. The WIRELESS light will
illuminate to indicate you are in WIRELESS mode. To turn
off,press and hold the POWER Button ( ) for 3 seconds
untilthe WIRELESS light turns off. The controller is also
equipped with an automatic power off function. If the
hand controller is not operated for 2 minutes it will turn off
automatically to conserve battery power.
The wireless hand controller can also be used in wired
Mode. When the cable is plugged in, the “Wired” light
will illuminate.
In the case of replacing a hand controller unit, or loss of pairing, a new controller
can be paired to the wireless receiver by following the steps below. If the wireless
receiver was previously paired to a hand controller, the previous pairing needs to
be cleared from the receiver memory first.
Note: The wireless receiver is located in the control box and is usually wired into
the vehicles ignition system or on a separate switch (refer to the wiring diagram
on Page 10). Turn the key or flick the switch to turn the wireless receiver ON or OFF.
ISOMETRIC VIEW
N.T.S.
FLAT PATTERN
.
SCALE
ISOMETRIC VIEW
N.T.S.
FLAT PATTERN
.
SCALE
Pairing the new Hand Controller
Clearing the Receiver Memory
1. Ensure the new wireless hand controller is turned OFF
2. Turn on the new wireless hand controller in wireless mode by pressing and holding the
POWER button ( ) for 3 seconds.
3. Press and hold the “IN” and “OUT” buttons on the new hand controller at the same
time. While continuing to press both buttons, the following process will happen:
1. Ensure that the wireless receiver is turned OFF.
2. Turn on the new wireless hand controller in wireless mode by pressing and holding the
POWER button ( ) for 3 seconds.
3. Press and hold the “IN” and “OUT” buttons on the new hand controller at the same
time. While continuing to press both buttons, the following process will happen:
a. The “WIRELESS” green indicator light and “Wired” red indicator light
will illuminate solidly for 6 seconds.
b. The two indicator lights will then flash slowly.
a. The “WIRELESS” green indicator light and “Wired” red indicator light will
illuminate solidly for 6 seconds.
b. The two indicator lights will then flash slowly for another 6 seconds.
c. The two indicator lights will then disappear for another 6 seconds.
d. The two indicator lights will then start to flash quickly.
Changing battery in the WIRELESS Hand controller
From the rear of the hand controller, remove the 6 screws as shown below.
Once the screws are removed, the rear half of the hand controller can be separated
allowing access to the battery. Replace the A23 battery and reassemble rear half of
hand controller. When reassembling the hand controller, ensure that the rubber seal is
aligned and not pinched. This will maintain the hand controller waterproof rating.
When the slow flashing begins, continue to hold the ”IN” and “OUT” buttons while
turning ON the wireless receiver. Keep pressing the “IN” and “OUT” buttons until the two
indicator lights disappear. Release the buttons and the hand controller is now paired.
When the quick flashing begins, continue to hold the ”IN” and “OUT” buttons while
turning ON the wireless receiver. Keep pressing the “IN” and “OUT” buttons until the two
indicator lights disappear. Release the buttons and the hand controller is now paired.
| REVO VEHICLE RECOVERY WINCH
|REVO VEHICLE RECOVERY WINCH
Page 15
Page 16
Содержание REVO 10
Страница 1: ...REVO 10S REVO 10W REVO 12S REVO 12W ...
Страница 24: ......