background image

MS1300P 
Manure Spreader

Service and Maintenance

35

9.8.2  Replace the Drive Belts

IMPORTANT!  Always replace drive belts as a matched set. 
Recheck the drive belt tension after 10 hours of use.

01462

2

1

Fig.  24 – 

Tensioning a Drive Belt

1. 

Remove the belt-drive shield.

2. 

Loosen (do not remove) the four bearing-mount bolts (2). 

3. 

Turn the drive belt tensioning nut (1) counterclockwise to 
loosen it.

4. 

Push down on the drive belts to pull the bearing over until 
the drive belts are loose enough to remove. 

5. 

Remove the drive belts, and then install a new set of belts. 

6. 

Slide the bearing to snug up the belts. 

7. 

Turn the belt tensioning nut clockwise to apply tension.

8. 

Check the drive belt tension. For instructions, see 

Adjust 

the Drive Belt Tension on page 34

.

9. 

Make sure that the pulley alignment is correct, and then 
tighten the four bearing-mount bolts. 

10. 

Reinstall the belt-drive shield.

9.9  Beater-bar Paddles

For optimal performance, inspect the beater-bar paddles on a 
regular basis and replace paddles that are worn or damaged. 
Contact your Bush Hog dealer to purchase replacement paddles.

2

1

3

01467

Fig.  25 – 

Paddle Replacement

1. 

Set the machine to a safe condition. For instructions, see 

Safe Condition on page 10

2. 

Remove the gearbox-coupler hex bolt and lock nut (1) to 
release the beater bar. 

3. 

Rotate the beater bar to access the required paddle (3).

4. 

Remove the three bolts and serrated nuts that secure 
the paddle to the paddle holder (2), and then remove the 
paddle.

5. 

Align a new paddle with the paddle-holder holes. 

6. 

Install the three bolts and nuts to secure the paddle to the 
paddle older (if required, use new fasteners).

7. 

Tighten the paddle bolts and nuts to the recommended 
torque. For more information, see 

Common Bolt Torque 

Values on page 38

.

8. 

Repeat Steps 3–7 for each additional paddle that requires 
replacement.

9. 

Align the beater-bar hole with the gearbox-coupler hole, and 
then install the hex bolt and lock nut to secure the beater 
bar.

10. 

Tighten the hex bolt and lock nut to the recommended 
torque.

Содержание MS1300P













































Отзывы: