Bush Hog BH400 Series Скачать руководство пользователя

Страница: 120 / 194

OPERATION

BH400/BH500 Series 10/19

Operation Section 4-22

•

Lift Type-Ensure the tailwheel support bolts are
properly installed and tightened.

•

Inspect all bolts and screws and tighten to the
recommended torque.

OPS-R-0039_H

•

Ensure the tractor PTO master shield and the
mower slip clutch shield are in place, lowered,
and in good condition.

•

Ensure the driveline integral shield is in good
condition and rotates freely.

•

Ensure the driveline slip clutch (if equipped) is
properly adjusted.

OPS-R-0039

•

Inspect the gearbox oil level. A low oil level is a
warning sign that the gearbox may be cracked
or its seal is damaged and needs replacement.

•

Ensure the gearbox vent is in place and free
from clogs.

OPS-R-0040_B

OPERA

TION

Содержание BH400 Series



































































































































































































Результаты поиска

Содержание BH400 Series

Отзывы:

Похожие инструкции для BH400 Series

Бренды по названию

Популярные бренды

Bush Hog BH400 Series, Руководство оператора

Результаты поиска

Содержание BH400 Series

Отзывы:

Похожие инструкции для BH400 Series

Бренды по названию

Популярные бренды