Bush Hog 3860 QT Скачать руководство пользователя | Manualshive

Страница: 20 / 46

background image

CARRYING THE LOAD

Position the bucket as low as possible below the
level of the tractor hood for maximum stability and
visibility, whether the bucket is loaded or empty.

Use extreme caution when operating the loader on a
slope and keep the bucket as low as possible. This
keeps the bucket and tractor center of gravity low
and will provide maximum tractor stability.

CAUTION

OPERATING THE LOADER ON A HILLSIDE
IS DANGEROUS. EXTREME CARE IS
RECOMMENDED.

DO THIS NOT THIS

When transporting the load, keep the bucket as low
as possible to avoid tipping, in case a wheel drops in
a rut.

NOT THIS

DO THIS

DUMPING THE BUCKET

Lift the bucket high enough to clear the side of the
vehicle. Move the tractor in as close to the side of
the vehicle as possible, then dump the bucket.

LOWERING THE BUCKET

After the bucket is dumped, back away from the
vehicle while lowering and rolling back the bucket.

FLOAT POSITION

LOWER

DUMP

RAISE

ROLLBACK

1-LEVER

CONTROL

DUMP

LOWER

FLOAT POSITION

ROLLBACK

RAISE

2-LEVER

CONTROLS

18

«
...
18
19
20
21
22
...
»

Содержание 3860 QT















































Отзывы:

Нет отзывов

Похожие инструкции для 3860 QT

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды