BUSCH R5 RD 0200 A Скачать руководство пользователя

Страница: 33 / 40

Troubleshooting | 12

Instruction Manual R5 RD 0200-0360 A_EN_en

33 | 40

Troubleshooting

DANGER

Live wires.
Risk of electrical shock.

●

Electrical installation work must only be executed by qualified personnel.

DANGER

Live wires. Carry out any work on the variable speed drive and motor.
Risk of electrical shock!

●

Electrical installation work must only be executed by qualified personnel.

CAUTION

Hot surface.
Risk of burns!

●

Prior to any action requiring touching the machine, let the machine cool down first.

Illustration showing parts that may be involved during troubleshooting:

CPL

Problem

Possible Cause

Remedy

The machine does not start.

The motor is not supplied with
the correct voltage.

●

Check the power supply.

The motor is defective.

●

Replace the motor.

The coupling (CPL) is defective.

●

Replace the coupling (CPL).

Содержание R5 RD 0200 A









































Результаты поиска

Содержание R5 RD 0200 A

Отзывы:

Похожие инструкции для R5 RD 0200 A

Бренды по названию

Популярные бренды

BUSCH R5 RD 0200 A, Инструкция по эксплуатации

Результаты поиска

Содержание R5 RD 0200 A

Отзывы:

Похожие инструкции для R5 RD 0200 A

Бренды по названию

Популярные бренды