background image

Installation | 6

Installation and Retrofit Instructions DOLPHIN LM 0530-0800 A, LT 0320-0630
A_EN_en

13 / 24

• Unscrew the temperature wire block from motor.

• Mount the adapter plate (pos. 2) with the flat gasket (pos. 6) and the four screws

(T40 M6x16) (pos. 3) (torque: 25NM).

6.2.3 Mount Variable-Frequency Drive

4x

4x

pos. 5

Flat gasket

VFD (pos. 1)

Lower part

VFD (pos. 1)

pos. 4

pos. 2

Pos. 7

• Remove the four screws and the housing cover of the variable-frequency drive to ac-

cess to the internal parts, beware the earth connection cable between the cover and
the housing.

• Disconnect spade earth connector from housing lid.

• Dissociate the lower part of the variable-frequency drive (pos. 1) from the housing by

unscrewing two M8 screws.

• Motor connection wires need to be completed before installing the lower VFD part.

• Use the wiring material (pos. 7) for motor connection.

• Mount the lower part and the flat gasket of the variable-frequency drive to the adapt-

er plate (pos. 2) with the four socket head screws and spring washers (pos. 4 and 5),
ensure supplied earth (PE) cable ring connector is secured on one of the screws.

• Reassemble the housing of the variable-frequency drive with the two screws (Torque

spec. M8: 25.0 NM) previously removed without forgetting the O-ring seal.

• Keep the variable-frequency drive's housing cover open for wiring.

DANGER

Risk of death due to electrical shock!

Death or serious injury!

• De-energise drive controller and secure it against being restarted.

Содержание LM 0530 A

























Отзывы: