BUSCH LM 0100 A Скачать руководство пользователя | Manualshive

Страница: 11 / 40

background image

Installation | 5

Instruction Manual DOLPHIN LM 0100-0800 A, LT 0130-0750 A_EN_en

11 | 40

5.2.3

Operating Liquid Connection

The machine cannot be operated without an operating liquid system. The following diagrams show
examples of typical installations. The actual scope of delivery is always contractually agreed upon.
If the machine is equipped with a VL System (see reference on the nameplate):

●

Consult the supplement to the instruction manual of the VL System for additional information.

OPI2**

GVC

DOLPHIN LM 0100-0800 A

DOLPHIN LT 0130-0750 A

OPI1

OPD

GVC

OPI

OPL

CPC

OPL

OPD

Description

CPC

Cavitation protection connection

GVC

Vacuum gauge or relief valve connec-
tion

OPD

Operating liquid drain

OPI

Operating liquid inlet

OPL

Operating liquid level plug

** OPI2 required for LM 0270 A, LM 0530 A and LM 0800 A only

Connection size:

Machine type

OPI1

OPI2

OPD

OPL

CPC

GVC

LM 0100-0180 A

Rc 1/2

N/A

Rc 1/8

Rc 1/4

N/A

Rc 1/4

LM 0270 A

Rc 1/2

Rc 1/2

Rc 1/8

Rc 1/4

N/A

Rc 1/4

LM 0530 A

Rc 1

Rc 1

Rc 1/4

Rc 3/4

N/A

Rc 3/4

LM 0800 A

Rc 1

Rc 1

Rc 1/2

Rc 3/4

N/A

Rc 3/4

LT 0130-0220 A

Rc 1/2

N/A

2 x Rc 1/8

Rc 1/4

Rc 1/8

Rc 1/4

LT 0320-0510 A

Rc 1

N/A

2 x Rc 1/4

Rc 3/4

Rc 1/4

Rc 3/4

LT 0630-0750 A

Rc 1

N/A

2 x Rc 1/2

Rc 3/4

Rc 1/4

Rc 3/4

●

Make sure that the operating liquid complies with the requirements, see

Operating Liquid Settings

«
...
9
10
11
12
13
...
»

Содержание LM 0100 A









































Отзывы:

Нет отзывов

Похожие инструкции для LM 0100 A

Бренд: GE Страницы: 28

Бренд: Paloma Страницы: 24

Бренд: Quooker Страницы: 12

Raypak Delta Limited 399B

Бренд: Rheem Страницы: 67

Бренд: Clarke Страницы: 16

Бренд: Kessel Страницы: 24

Бренд: ICI Caldaie Страницы: 48

Бренд: P.Lindberg Страницы: 46

Бренд: Bard Страницы: 42

Бренд: Zodiac Страницы: 16

Бренд: Kawamoto Pump Страницы: 28

Бренд: Oase Страницы: 76

Бренд: Graco Страницы: 28

Бренд: Gianneschi Страницы: 28

Бренд: clage Страницы: 24

Бренд: Remco Страницы: 5

Бренд: GDH Страницы: 24

Бренд: Samoa Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды