BUSCH LM 0100 A Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

background image

6 | Electrical Connection

18 | 40

Instruction Manual DOLPHIN LM 0100-0800 A, LT 0130-0750 A_EN_en

6.3

Wiring Diagram Three-Phase Motor

NOTICE

Incorrect direction of rotation.
Risk of damage to the machine!

●

Operation in the wrong direction of rotation can destroy the machine in a short time! Prior to
start-up, ensure that the machine is operated in the right direction.

NOTICE

Incorrect direction of rotation.
Risk of damage to the vacuum system!

●

Operating the vacuum system with the rotation in the wrong direction can result in the operating
liquid flowing back to the vacuum system. Prior to start-up, check for correct direction of rotation.

The intended rotation direction of the motor is defined by the illustration below:

●

Watch the fan wheel of the motor and determine the direction of rotation just before the fan
wheel stops.

If the rotation of the motor must be changed:

●

Switch any two of the motor phase wires.

«
...
16
17
18
19
20
...
»

Содержание LM 0100 A









































Отзывы:

Нет отзывов

Похожие инструкции для LM 0100 A

Бренд: Waterous Страницы: 36

Бренд: Paragon Страницы: 16

Бренд: Watts Страницы: 8

Bell & Gossett ecocirc XL Series

Бренд: Xylem Страницы: 62

Бренд: AmeriWater Страницы: 16

American Pride ACNF Series

Бренд: Amana Страницы: 8

Бренд: Barracuda PUMPS Страницы: 4

Бренд: Wilden Страницы: 32

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренд: Ocean Technologies Страницы: 2

FXV-1212C-32Q-M/Q

Бренд: BAC Страницы: 47

Бренд: Annovi Reverberi Страницы: 16

Бренд: Walrus Pump Страницы: 12

JABSCO 18670 Series

Бренд: Xylem Страницы: 16

Бренд: Yardworks Страницы: 18

Бренд: GE Страницы: 24

Бренд: Pentair Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды