manualshive.com logo in svg

Burkert 8691 REV.3, Руководство по эксплуатации, Страница: 43 / 64

Поделиться
Скачать
Burkert 8691 REV.3 Скачать руководство пользователя страница 43

43

Start-up

Inv.ValveDir LED

Pilot LED 

Key 1

Manual LED

Status  indicator  

Key 2

Figure 39: 

Operating and display elements

0 s

5 s

10 s

Manual LED

Inv.ValveDir LED

Start manual  

teach function

1

1

End of teach function

Status indicator

Figure 40: 

Start automatic teach function

 

→

Air bleed the pneumatic actuator: move to the unactuated end position.

 

→

Press and hold key 1 to start the manual teach function for >10 s (red manual LED + green Inv.ValveDir 

LED flash together: the first 5 s slowly, the second 5 s quickly, >10 s slowly again, then release key 1).

  The status indicator flashes orange while the manual teach function is running (function check).

 

→

Check whether the pneumatic actuator is in the deaerated, unactuated end position.

 

→

Confirm this end position by briefly pressing key 1.

 Yellow Pilot LED is lit.

 

→

Move the pneumatic actuator into the aerated, switched end position.

 

→

Confirm this end position by briefly pressing key 1.

 Yellow Pilot LED is not lit.

 

→

Air bleed the pneumatic actuator: move to the unactuated end position.

  When the status indicator stops flashing orange, the teach function is complete.

  

The end positions of the valve have been identified and saved.

Note: If the status indicator is lit red, the teach function is faulty and must be repeated.

 

→

Check that the seal (body casing) is in the correct position.

NOTE

Damage or malfunction due to ingress of dirt or moisture.

To observe the degree of protection IP65 or IP67:

 

▶

Screw in body casing to the stop.

 

→

Close the device (see accessories for assembly tool).

english

Type 8691 REV.3

Содержание 8691 REV.3

































































Отзывы:

Нет отзывов