background image

7

29112 060509

CLEANING

The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur-

faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device.

1 x 24h

   

37254.0000A  07/04  © 2004 BUNN-O-MATIC CORPORATION

NOTICE

The cleaning instructions noted above are for non-dairy sugar based food products.  When dispensing any other food product,

the cleaning cycle for the whipping chamber assembly and ejector elbow must be performed daily.

NOTA:

Las instrucciones de limpieza descritas anteriormente excluyen productos lacteos azucarados. La limpieza de las camaras

de mezcla y de los codos de salida de cada tolva deberá realizarse diariamente.

1 x 7d 

a. Wash 

b. Rinse 

c. Sanitize 

d. Dry 

a. Lave 

b. Enjuague 

c. Desinfecte 

d. Seque 

7

Replace Light Bulbs

as required.

1.  Para limpiar las camaras de mezcla, coloque el interruptor en la 

posicón ENJUAGUE/MARCHA (”RINSE/RUN”) y pulse el boton 

  para espumar y distribuir la bebida (”DISPENSE”). 

2.  Gire el codo hacia arriba, remueva las tolvas, llene las tolvas con 

producto y coloque las tolvas nuevamente en la maquina. 

3.  Vacie la bandeja de goteo y limpiela con un detergente liquido 

suave no abrasivo. 

1.  Rinse out Whipper Chambers by placing RINSE/RUN 

switch in the "RINSE" position and activating DISPENSE 

switches. 

2.  Turn elbow up, remove Hoppers, refill with product and 

replace hoppers into dispenser

3.  Empty Drip Tray and wash in a solution of dish detergent. 

Cambie los bombillos

quemados cuando

sea necesario.

Содержание FMD-1









Отзывы: