background image

3

INTRODUCTION

This equipment dispenses hot beverages or soups on demand from powered product.  It is for indoor use only 

on a sturdy counter or shelf.

00656.0001

00831.0000

FMD-1 28328.0004

28368.0003

FMD-2 28328.0005

27096.0000  FMD-1 ONLY

28964.0000

28964.0001

29112 051111

CONTROL THERMOSTAT ADJUSTMENT

APPROXIMATE  THERMOSTAT  TEMPERATURE  SETTINGS

200

 F

190

 F

180

 F

28368.0003A  08/08  

©  

2008 BUNN-O-MATIC CORPORATION

USER NOTICES

Carefully read and follow all notices on the equipment and in this manual.  They were written for your protection. 

All notices are to be kept in good condition.  Replace any unreadable or damaged labels.

37881.0000

As directed in the International Plumbing Code of the 

International  Code  Council  and  the  Food  Code 

Manual of the Food and Drug Administration (FDA), 

this  equipment  must  be  installed  with  adequate 

backflow  prevention  to  comply  with  federal,  state 

and  local  codes.  For  models  installed  outside  the 

U.S.A., you must comply with the applicable Plumb-

ing /Sanitation Code for your area.

Artwork for P/N:  00656.0001
Artwork Rev:  A
Drawn:  REF
Date:  04/22/10

00824.0002

Содержание FMD-1









Отзывы: