Bull NovaScale T860 E1 Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 370

background image

8-10

POST Error Messages

When the POST detects an error, it displays an error message on the display unit screen. The following table lists the
error messages, their descriptions, and the actions to take.

IMPORTANT:

Note the messages that are displayed before consulting with your service

representative. Alarm messages include useful information for maintenance.

Error
code

Error message

Recommended Action

0200

Failure Fixed Disk.

Contact your service representative.

0210

Stuck Key.

Disconnect the keyboard and connect it again.

0211 Keyboard

error

Disconnect the keyboard and connect it again. If it
does not correct the error, contact your service
representative.

0213

Keyboard locked - Unlock key switch.

Release the lock of the key switch. If it does not correct
the error, contact your service representative.

0220

Monitor type does not match CMOS - Run
SETUP.

Start the SETUP.. If it does not correct the error, contact
your service representative.

0230

System RAM Failed at offset.

0231

Shadow Ram Failed at offset.

0232

Extended RAM Failed at address line.

Contact your service representative.

0250

System battery is dead - Replace and run
SETUP.

Contact your service representative to replace the
battery. (After restarting the computer, start the SETUP
to provide the settings again.)

0251

System CMOS checksum bad - Default
configuration used.

The default values have just been set. Start the SETUP
to provide the settings again. If it does not correct the
error, contact your service representative.

0252

Password checksum bad - Passwords
cleared.

The password has just been cleared. Start the SETUP to
provide the settings again.

0260

System timer error.

0270

Real time clock error.

0271

Check date and time setting.

Start the SETUP to set the date and time again. If the
error occurs successively in spite of the resetting,
contact your service representative.

0280

Previous boot incomplete - Default
configuration used.

Start the SETUP to provide the settings again.

0281

Memory size found by POST differed from
EISA CMOS.

Initialize the EISA CMOS.

02D0

System cache error - Cache disabled.

The cache cannot be used. Contact your service
representative.

«
...
198
199
200
201
202
...
»

Содержание NovaScale T860 E1



















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NovaScale T860 E1

Бренд: Crown Страницы: 12

Бренд: Watchguard Страницы: 32

Бренд: Rackable Systems Страницы: 4

Бренд: Ubiquiti Страницы: 28

Бренд: Gigabyte Страницы: 2

Бренд: Abit Страницы: 56

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

DeviceMaster PRO

Бренд: Comtrol Страницы: 174

cPCI-6510 Series

Бренд: ADLINK Technology Страницы: 112

Бренд: R/Evolution Страницы: 130

Бренд: GeoVision Страницы: 73

Бренд: Sugon Страницы: 155

Serial Servers Vlinx VESR9xx

Бренд: Vlinx Страницы: 65

2-Bay SATA NAS RAID Server NAS-7200

Бренд: Planet Страницы: 80

33459 - StorCenter Pro NAS 250d/500GB Server

Бренд: Iomega Страницы: 20

Бренд: Gigabyte Страницы: 106

Бренд: Oracle Страницы: 44

Бренд: Oracle Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды