background image

2

Introduction 2-5

Safety symbol and signal word review ....................... 2

Preparing your garage door ....................................... 3

Tools needed .............................................................. 3

Planning  .................................................................... 4

Carton inventory ......................................................... 5

Hardware inventory .................................................... 5

Assembly  

6-7

Attach the rail to the motor unit .................................. 6

Attach the chain to the sprocket ................................. 6

Tighten the chain ........................................................ 7

Installation  

7-22

Installation safety instructions .................................... 7

Determine the header bracket location ...................... 8

Install the header bracket ........................................... 9

Attach the rail to the header bracket ........................ 10

Position the opener .................................................. 11

Hang the opener ....................................................... 12

Install the door control .............................................. 13

Install the light .......................................................... 14

Attach the emergency release rope and handle ...... 14

Electrical requirements ............................................. 15

Install the Protector System

®

 ............................... 16-18

Fasten the door bracket ...................................... 19-20

Connect the door arm to the trolley ..................... 21-22

Adjustment 23-25

Adjust the travel limits .............................................. 23

Adjust the force ........................................................ 24

Test the safety reversal system ............................... 25

Test the Protector System

®

 ...................................... 25

Operation   

26-30

Operation safety instructions .................................... 26

Using your garage door opener ............................... 26

Using the wall-mounted door control ........................ 27

To open the door manually ...................................... 27

Care of your garage door opener ............................. 28

Having a problem? ................................................... 29

Diagnostic chart ........................................................ 30

Programming 31-32

To add or reprogram a hand-held remote control .... 31

To erase all codes .................................................... 31

3-Button remotes ...................................................... 31

To add, reprogram or change 
a Keyless Entry PIN ................................................. 32

Repair Parts   

33-34

Rail assembly parts .................................................. 33

Installation parts ....................................................... 33

Motor unit assembly parts ........................................ 34

Accessories 35

Repair Parts and Service 

36

Warranty 36

TABLE OF CONTENTS

When you see these Safety Symbols and Signal 
Words on the following pages, they will alert you to 
the possibility of 

serious injury or death

 if you do 

not comply with the warnings that accompany them. 
The hazard may come from something mechanical 
or from electric shock. Read the warnings carefully.

When you see this Signal Word on the following 
pages, it will alert you to the possibility of damage to 
your garage door and/or the garage door opener if 
you do not comply with the cautionary statements 
that accompany it. Read them carefully.

INTRODUCTION

Safety Symbol 
and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided it is installed, operated, 
maintained and tested in strict accordance with the instructions and warnings contained in this manual.

Mechanical

Electrical

Содержание 3255BM 1/2 HP





































Отзывы: