Buell XB 2010 Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 714

background image

2.42

RIGHT TAIL SECTION: LIGHTNING MODELS

DISASSEMBLY

1.

Remove seat.

Disconnect negative (-) battery cable first. If positive (+)
cable should contact ground with negative (-) cable con-
nected, the resulting sparks can cause a battery explosion,
which could result in death or serious injury. (00049a)

2.

. Disconnect battery cables from battery:

negative cable (black) first.

3.

Remove battery.

4.

Disconnect:

a.

Right side ground terminals (3) [GRD1] & [GRD 3].

b.

Rear brake light switch connector (4) [121].

5.

Remove right side passenger footrest assembly. See

2.34 FOOTPEG, HEEL GUARD AND MOUNT: FIREBOLT
AND LIGHTNING MODELS

.

6.

Remove master cylinder remote reservoir. See

BRAKE MASTER CYLINDER

.

7.

See

. Remove right front trunk pan fastener

(1).

8.

Remove fastener securing battery tray to right side tail
section (XB12Ss models only).

9.

Remove fasteners securing center tail section to right tail
section.

10. See

. Remove fasteners (1) securing right

tail section to main frame/fuel tank assembly.

11. Remove right tail section.

ASSEMBLY

1.

. Install right tail section (16) onto vehicle.

a.

Install fastener (14) attaching right front trunk pan to
right side tail section and tighten to 12-36 in-lbs (1.4-
4 Nm).

b.

On XB12Ss models, apply LOCTITE 271 (red) and
install battery tray fasteners and tighten to 48-72 in-
lbs (5.4-8 Nm).

c.

Apply LOCTITE 271 (red) and install center tail sec-
tion fastener to rear tail section (15).Tighten to 102-
114 in-lbs (11.5-12.8 Nm).

d.

Apply LOCTITE 271 (red) and install fasteners
attaching left and right tail sections to main frame/fuel
tank assembly and tighten to 21-23 ft-lbs (28.5-31.2
Nm).

2.

Install master cylinder remote reservoir. See

BRAKE MASTER CYLINDER

3.

Install right side passenger footrest support assembly.
See

2.34 FOOTPEG, HEEL GUARD AND MOUNT:

FIREBOLT AND LIGHTNING MODELS

Be sure that all lights and switches operate properly before
operating motorcycle. Low visibility of rider can result in
death or serious injury. (00316a)

4.

Connect:

a.

Right side ground terminals (6) [GRD1] and [GRD 3].

b.

Rear brake light switch connector (5) [121].

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

5.

Install and connect battery. See

1.16 BATTERY MAINTEN-

.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

6.

Install seat.

2010 XB Service: Chassis 2-151

«
...
229
230
231
232
233
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: MadStad Engineering Страницы: 2

Бренд: Yoshimura Страницы: 7

Бренд: PEUGEOT Страницы: 12

Бренд: hepco & becker Страницы: 5

Бренд: Romet Страницы: 52

Бренд: Big Bike Parts Страницы: 3

Бренд: DYNATEK Страницы: 12

Бренд: Shark Страницы: 92

Бренд: Aim Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 41

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 101

Бренд: Yamaha Страницы: 102

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды