manualshive.com logo in svg

Buell XB 2010, Руководство по обслуживанию

Сервисный мануал Buell XB 2010 теперь доступен для скачивания бесплатно. Убедитесь, что ваш мотоцикл всегда на ходу благодаря этому надежному руководству. Скачайте его сейчас с manualshive.com и получите всю необходимую информацию для обслуживания вашего мотоцикла.

Поделиться
Скачать
background image

ASSEMBLY

NOTE

See 

Figure 2-193

. There are two threaded plastic lugs (14) on

the trunk pan that are used for manufacturing purposes only.

1.

Install trunk pan assembly (11) from left side of vehicle.

2.

Install fastener (8) securing right front trunk pan to right
side tail section and tighten to 12-36 in-lbs (1.4-4 Nm).

3.

Install right side passenger footrest support assembly.
See 

2.34 FOOTPEG, HEEL GUARD AND MOUNT:

FIREBOLT AND LIGHTNING MODELS

.

4.

Install two fasteners (12) securing trunk pan to center tail
section and leave loose.

5.

Install left tail section (5) onto vehicle.

a.

Install fastener (8) attaching left front trunk pan to left
side tail section and tighten to 72-96 in-lbs (8-10.8
Nm).

b.

Apply LOCTITE 271 (red) and install fasteners (4)
attaching left rear tail section to center tail section and
tighten to 102-114 in-lbs (11.5-12.8 Nm).

c.

Apply LOCTITE 271 (red) and install fasteners (1)
attaching left tail section to main frame/fuel tank
assembly and tighten to 21-23 ft-lbs (28.5-31.2 Nm).

d.

Apply LOCTITE 271 (red) and install fasteners
securing battery tray to side castings and tighten to
48-72 in-lbs (5.4-8 Nm).

6.

Tighten fasteners (12) securing trunk pan to center tail
section to 48-72 in-lbs (5.4-8 Nm).

7.

Install left side passenger footrest support assembly. See

2.34 FOOTPEG, HEEL GUARD AND MOUNT: FIREBOLT
AND LIGHTNING MODELS

.

8.

Move rear main harness and shock absorber reservoir
back to left side of vehicle.

Be sure that all lights and switches operate properly before
operating motorcycle. Low visibility of rider can result in
death or serious injury. (00316a)

9.

See 

Figure 2-192

. Connect:

a.

Wire harness ground (2) [GRD 2].

b.

Rear brake light switch connector (5) [121].

c.

ECM connectors (7) [10, 11] and [164] (on XB12
models).

d.

BAS (bank angle sensor) connector (9) [134].

e.

Right turn signal connector (11) [18].

f.

Left turn signal connector (10) [19].

g.

License plate lamp connector (12) [45]

h.

Tail light connectors (13) [93].

i.

Ground terminals on right side tail section (6) [GRD
1] & [GRD 3].

10. Attach cable strap loosely securing the BAS harness to

the seat latch cable.

11. Install the rear shock absorber reservoir into bracket and

tighten fastener. See 

2.23 REAR SHOCK ABSORBER

.

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

12. Install and connect battery. See 

1.16 BATTERY MAINTEN-

ANCE

.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

13. Install seat.

HOME

2-148  2010 XB Service: Chassis

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

DAELIM ROADWIN - Brochure preview
ROADWIN -
Бренд: DAELIM Страницы: 2
Kabuto HIKE Instruction Manual preview
HIKE
Бренд: Kabuto Страницы: 40
HYOSUNG GD250 Owner'S Manual preview
GD250
Бренд: HYOSUNG Страницы: 98
Bajaj Pulsar N160 Owner'S Manual preview
Pulsar N160
Бренд: Bajaj Страницы: 55
HRC '92-RS125R Owner'S Manual preview
'92-RS125R
Бренд: HRC Страницы: 88
Dakota Digital MCL-30K-SPD Installation Manual preview
MCL-30K-SPD
Бренд: Dakota Digital Страницы: 7
METRAKIT MINI50 GP 2009 Owner'S Manual preview
MINI50 GP 2009
Бренд: METRAKIT Страницы: 53
AFX FX-78 Owner'S Manual preview
FX-78
Бренд: AFX Страницы: 52
W&W Cycles 13-815 Quick Start Manual preview
13-815
Бренд: W&W Cycles Страницы: 5
YCF FACTORY SP2 Owner'S Manual preview
FACTORY SP2
Бренд: YCF Страницы: 78
Custom Dynamics Magic Strobes Installation Instructions preview
Magic Strobes
Бренд: Custom Dynamics Страницы: 2
Royal Enfield ELECTRA Service Manual preview
ELECTRA
Бренд: Royal Enfield Страницы: 234
DYNATEK D2K-HD1E User Instructions preview
D2K-HD1E
Бренд: DYNATEK Страницы: 10
Wunderlich 8166235 User Manual preview
8166235
Бренд: Wunderlich Страницы: 1
Wunderlich 31962-002 Fitting Instruction preview
31962-002
Бренд: Wunderlich Страницы: 2
Wunderlich 43520-222 Manual preview
43520-222
Бренд: Wunderlich Страницы: 5
Wunderlich 35835-002 Manual preview
35835-002
Бренд: Wunderlich Страницы: 5
Wunderlich 30471 Series Fitting Instruction preview
30471 Series
Бренд: Wunderlich Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды