Buehler 11-2675 Скачать руководство пользователя страница 34

Страница: 34 / 66

MA112680_39.3

[Original Instructions]

4/2014

Troubleshooting Chart

Problem

Possible Cause

Correction

The IsoMet does not power on

The unit is not plugged in

Check the power cord
connection

The unit is not powered on

Check the rear power switch

The pump has lost pressure

Fluid level may be too low

Fill the fluid to the correct level

Tank screen may need cleaning

Remove screen and clean

Suction hose clogged

Remove and check suction and
flexible hose for blockages and
clear blockages

Flexible hoses clogged or
blocked

The blade keeps pinching

Wrong blade for the material

Replace with correct blade

Improper specimen fixture
(primary cause)

Use correct specimen fixture

Blade may need to be dressed

Dress blade

The FEED RATE may be too
slow

Increase FEED RATE

BLADE SPEED may be too slow

Increase BLADE SPEED

The blade keeps stopping

The CUTTING DISTANCE may
have changed

Reset the CUTTING DISTANCE

The DISTANCE REMAINING
may be .00 or less

Increase the DISTANCE
REMAINING

The ARM LIMIT switch may be
activated

Deactivate the ARM LIMIT switch

The bed has rust on it

Improper coolant mixture

Check the coolant for proper
mixture

The hood has been closed too
long with moisture build up

Open hood and keep hood open
when not in use

The Specimen Positioning
System does not move

Cable is disconnected

Check the cable connection

The Blade Dressing does not
work

Cable is disconnected

Check the cable connection

Dressing stick in the wrong
position

Check the dressing stick position
and clean it

The Rotating Chuck does not
work

Cable is disconnected

Check the cable connection

Rotating chuck is not powered on

Make certain the Rotating Chuck
is turned on

The Blade Turret completed one
cycle but won’t advance for a
second cut

The IsoMet is operating as if the
Precision Table is still attached

Turn the unit off then back on.

Coolant leaks from the IsoMet

Table or unit is not level

Make certain the table is level

Coolant level too high

Check the volume of cutting fluid

Содержание 11-2675



































































Результаты поиска

Содержание 11-2675

Отзывы:

Бренды по названию

Популярные бренды

Buehler 11-2675, Руководство пользователя

Результаты поиска

Содержание 11-2675

Отзывы:

Бренды по названию

Популярные бренды