manualshive.com logo in svg

Buehler 11-2675, Руководство пользователя

Поделиться
Скачать
Buehler 11-2675 Скачать руководство пользователя страница 10

 

4 

MA112680_39.3 

[Original Instructions] 

4/2014 

Installation  

WARNING

!

 

Equipment Damage. The IsoMet 4000 Linear Precision Saw is heavy. Follow local safety practices 
to lift the IsoMet 4000 Linear Precision Saw unit from the shipping carton. Improper lifting can 
result in machine damage. 

Personal Injury. Improper lifting of the IsoMet 4000 Linear Precision Saw can result in personal 
injury. 

The IsoMet 4000 Linear Precision Saw is bolted to a wooden base for protection during shipping. Open 
areas are provided at the corners of the base for ease of lifting.  

Lift the IsoMet 4000 Linear Precision Saw

 

out of the carton and position it on a table so it overhangs the 

edge. Remove all bolts securing the IsoMet 4000 Linear Precision Saw to the wood base. 

Select a location for your IsoMet 4000 Linear Precision Saw that provides an adequate working space, a 
power source, water connections, and a drain.  

Allow 6 inches (150 mm) of space at the back of the IsoMet 4000 Linear Precision Saw for raising the 
hood.  

Electrical Installation 

 

Electrical Shock Hazard. Only a qualified electrical technician should perform electrical 
installation and maintenance.  

Electrical Shock Hazard. Do not change the power plug in any way. Buehler machines are 
equipped with a polarized plug (one blade is wider than the other) and a ground pin. Polarized 
plugs reduce the risk of electrical shock. This plug will fit in a polarized outlet only one way.  

•

 

Disconnect the power supply before making any electrical adjustments. Install a lockout tag 
and follow lockout tag procedures to prevent any accidental starting of the machine. 

•

 

Capacitors inside the machine may retain a charge even if the machine is disconnected from 
the power supply 

Installation of the IsoMet 4000 Linear Precision Saw must comply with local electrical standards or codes 
of practice.

 

The Specification Plate is located on the back of the IsoMet 4000 Linear Precision Saw. Check that the 
Specification Plate values for voltage, current, and power consumption are compatible with the intended 
electrical supply before installation. 

The IsoMet 4000 Linear Precision Saw can be plugged into an existing outlet rated for the voltage and 
frequency listed on the Specification Plate. 

Содержание 11-2675



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды