manualshive.com logo in svg

Buderus FM443, Инструкция по установке и обслуживанию, Страница: 50 / 56

Поделиться
Скачать
Buderus FM443 Скачать руководство пользователя страница 50

FM443 Function module - We reserve the right to make technical modifications.

50

Monitor data

7

 

The position of the 3-way valve depends on the installed valve type 
in this case. Check whether the 3-way valve was correctly installed 
on the building.

direct

The return temperature of the heating system is higher than the 
temperature in the lower part of the buffer or combi storage tank. 

The heater return is sent directly to the boiler.

The 3-way valve is in the "bypass" position.

tank

The return temperature of the heating system is lower than the 
temperature in the buffer or in the lower part of the combi storage 
tank. 

The heater return is sent through the buffer or combination tank for 
preheating by the 3-way switching valve.

7.3

Solar circuit heat meter

The display shows the current flow of the flow meter (heat meter 
kit) and the corresponding supply and return temperatures of the 
solar circuit.

monitor SOLAR

Volume

238gal/h

supply

194°F

return

86°F

Содержание FM443

























































Отзывы:

Нет отзывов