Buderus FM443 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 56

Buderus FM443 Скачать руководство пользователя страница 18

FM443 Function module - We reserve the right to make technical modifications.

18

The functions of the FM443

3

3.2

Changing the operating mode

You can change the operating mode of the solar control. The
operating modes are as follows:

–

Manual ON ("day mode" button)

–

Manual OFF ("night mode" button)

–

Automatic operation ("AUT" button)

Open the flap of the MEC2 remote control.
Press and hold the "heating zone" button.

Turn the dial until "select heat zone – solar" appears on the display.

Release the "heating zone" button.

USER NOTE

With the operating mode "Manual ON" ("day mode" button), the
collector protection function is switched on.

USER NOTE

When the flap on the MEC2 remote control is closed, it generally
indicates the heating zone to which the MEC2 remote control is
assigned. If the MEC2 remote control is not assigned to any
heating zone, then the lowest installed heating zone is always
indicated.

For more information see the technical documentation for your
control panel.

«
...
16
17
18
19
20
...
»

Содержание FM443

























































Отзывы:

Нет отзывов