btsr SMART CLEARER страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 81

background image

Operation

- 3.30 -

SMART CLEARER

SENSOR TEST - Sensors Test

SETUP

CONFIG

TEST

SENSOR

This function gives you the possibility to check communications between the
SMART CLEARER terminal and (one by one) each of the connected sensors.
In this way it is possible to check that:

All sensors are correctly numbered and identified

All sensors respond correctly to the terminal

The same number has not been assigned to more that 1 sensor.

This function is particularly useful during the testing phase (immediately after
installation) and when operation problems occur which require a check of each
sensor individually.
The test does not send any diagnostic message to the SMART system display!
The operator shall simply select the number of the desired sensor (DEV XXX) by
using the button NEXT CY and checking that the red LED of the selected sensor is
flashing.

Press

until the TEST CONFIG option is displayed.

Press

to have access to the Test function.

This screen indicates that the sensor test is going to start.

Press

to continue.

DEV XXX indicates the sensor which is being tested

(initially sensor no. 1).

Check

that the Red LED of sensor XXX is flashing and there are no other sensors with the
Red LED FLASHING.

If the Red LED of the sensor that should respond to the number XXX is not
flashing, it means that the sensor is faulty or that the sensors numbering
procedure has not been performed correctly. In this case try to renumber the
sensors (refer to “Parameters setting for initial installation") and, if required,
replace the sensor.

If the Red LED is flashing on more than one sensor, it means that the same
number has been assigned to more than one sensor. In this case it will be
necessary to repeat the sensor numbering procedure (refer to “Parameters
setting for initial installation”).

Press

to select the next sensor and check that the Red LED of the selected

sensor is flashing.

Repeat this test on all connected sensors.

Press

once to leave this function, or press it several times to return to the

Main Menu.

«
...
40
41
42
43
44
...
»

Содержание SMART CLEARER


















































































Отзывы:

Нет отзывов

Похожие инструкции для SMART CLEARER

Бренд: Jabra Страницы: 4

Бренд: Nabco Страницы: 35

Бренд: Parker Страницы: 12

Бренд: Koer Страницы: 6

Бренд: ABB Страницы: 17

Бренд: Jetter Страницы: 24

Бренд: Challenger Lifts Страницы: 20

Бренд: Klimaire Страницы: 5

Бренд: MAHA Страницы: 23

Бренд: Dantel Страницы: 6

GAMMA VERSUS Series

Бренд: JCM Страницы: 111

767-4804/000-800

Бренд: WAGO Страницы: 80

Бренд: TUYA Страницы: 28

MultiLoad II EXL

Бренд: Toptech Страницы: 83

Бренд: M-system Страницы: 4

Бренд: Hearth Products Controls Страницы: 5

Бренд: Sensitron Страницы: 32

Бренд: Danfoss Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды