background image

12

GENERAL SPECIFICATION

Display:

3-5/6 digits 6,000 counts

Update Rate:

5 per second nominal

24 Segments Bar graph:

40 per second max

Operating Temperature:

0

o

C to 40

o

C

Relative Humidity:

Maximum relative humidity 80% for temperature up to 31

o

C decreasing linearly

to 50% relative humidity at 40

o

C

Altitude:

Operating below 2000m

Storage Temperature:

-20

o

C ~ 60

o

C, < 80% R.H. (with battery removed)

Temperature Coefficient:

Nominal 0.15 x (specified accuracy)/

o

C @ (0

o

C ~ 18

o

C or 28

o

C ~ 40

o

C),

or otherwise specified

Sensing:

Model 251, 252 & 255:

Average sensing

Model 257:

True RMS sensing

Pollution Degree:

2

Safety:

Double insulation per IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. &

CAN/CSA C22.2 No. 61010.1-0.92 to Category II 1000V, CAT III 600V and CAT IV 300V AC & DC

Transient Protection:

6.5kV (1.2/50

s surge)

Terminals (to COM) Measurement Category:

V :

Category II 1000V, CAT III 600V and CAT IV 300V AC & DC.

mA

A :

Category III 500Vac and 300Vdc.

A :

Category III 600Vac and 300Vdc.

E.M.C. :

Meets EN61326-1:2006 (EN55022, EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-

3, EN61000-4-4, , EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11)

In an RF field of 3V/m:

Capacitance function is not specified

Other function ranges:

Total Accuracy = Specified Ac 100 digits

Performance above 3V/m is not specified

Overload Protection:

uA & mA:

0.63A/500Vac, IR

50kA

@500Vac

A:

10A/600Vac IR 100kA @600Vac

V:

1050 Vrms, 1450 Vpeak

AutoCheck

TM

, mV, Ohm & others:

600 Vrms

Low Battery:

Below approx. 2.3V

Power Supply:

1.5V AAA Size battery X 2

Power Consumption (typical):

3.5mA

APO Consumption (typical):

10

A

APO Timing:

Idle for 34 minutes

Dimension:

161*80*50mm L*W*H (With Holster)

Weight:

Approx. 340 gm (With Holster)

Special Features:

AutoCheck

TM

V &

(model 255 & 257 only)

; Auto-ranging MAX/MIN Record

(

model 255 & 257 only

); Crest mode (Peak Hold,

model 255 & 257 only

), Backlighted LCD (

model

255 & 257 only

); Auto-ranging Relative Zero mode; Display Hold; EF-Detection (NCV); Interface

capabilities with PC computer; Input warning detection

Содержание BM251

















Отзывы: