Bryant 580J*04A Скачать руководство пользователя страница 18

Страница: 18 / 52

CONVENIENCE OUTLETS

Two types of convenience outlets are offered on 580J mod-

els: Non-powered and unit-powered. Both types provide a 125-

volt GFCI (ground-fault circuit-interrupter) duplex receptacle

rated at 15-A behind a hinged waterproof access cover, located

on the end panel of the unit. See Fig. 26 for amp limitations.

See Fig. 27 for convenience outlet location.

Fig. 26 — Convenience Outlet Utilization Notice Label

NOTE: Unit powered convenience outlets are not available

as factory installed options for single phase (-J voltage

code) models.

Fig. 27 — Convenience Outlet Location

Installing Weatherproof Cover — A weatherproof while-in-

us cover for the factory-installed conenience outlets is now re-

quired by UL standards. This cover cannot be factory-mounted

due its depth; it must be installed at unit installation. For ship-

ment, the convenience outlet is covered with a blank cover

plate.

On units with electro-mechanical controls the weatherproof

cover kit is shipped in the unit’s control box. The kit includes

the hinged cover, a backing plate and gasket.
On units with the factory installed RTU Open option the

weatherproof cover kit is secured to the basepan underneath

the control box. See Fig. 28.

Fig. 28 — Weatherproof Cover — Shipping Location on

Units with Factory Installed RTU Open

Remove the blank cover plate at the convenience outlet.
Loosen the two screws at the GFCI duplex outlet, until ap-

proximately

-in. (13 mm) under screw heads are exposed.

Press the gasket over the screw heads. Slip the backing plate

over the screw heads at the keyhole slots and align with the

gasket; tighten the two screws until snug (do not over-tighten).

Mount the weatherproof cover to the backing plate as

shown in Fig. 29. Remove two slot fillers in the bottom of the

cover to permit service tool cords to exit the cover. Check for

full closing and latching.

Fig. 29 — Weatherproof Cover Installation

WARNING

Failure to follow this warning could result in personal

injury or death.
Units with convenience outlet circuits may use multiple

disconnects. Check convenience outlet for power status

before opening unit for service. Locate its disconnect

switch, if appropriate, and open it. Lock-out and tag-out

this switch, if necessary.

Convenience

tlet

GFCI

Pwd-CO

witch

Pwd-CO

former

Control Box

Acce

nel

IMPORTANT: DISCONNECT ALL POWER TO

UNIT AND CONVENIENCE OUTLET. LOCK-OUT

AND TAG-OUT ALL POWER PRIOR TO INSTAL-

LATION.

Weatherproof

Cover

RECEPTACLE
NOT SHOWN

COVER – WHILE-IN-USE
WEATHERPROOF

BASE PLATE FOR
GFCI RECEPTACLE

Содержание 580J*04A





















































Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды

Bryant 580J*04A, Руководство по установке

Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды